Skip to content
Tinkercaster

Seymour Duncan wiring

Everything Axe set with a five-way blade, volume and tone

Three four-conductor single-coil-sized pickups · Five-way blade · One volume · One tone

Seymour Duncan Everything Axe set: neck, middle and bridge four-conductor pickups on a five-way blade with one 250k volume, one 250k tone and a .047 cap. Neck and bridge run with red and white joined and taped; the middle pickup's black and red go to the switch together and its white is grounded with the green and bare.

Viewed from the back of the controls, as you solder them.

Everything Axe set with a five-way blade, volume and toneEverything Axe set with a five-way blade, volume and tone: Three four-conductor single-coil-sized pickups · Five-way blade · One volume · One tone. Original Tinkercaster drawing with labelled terminals.Neck pickupMiddle pickupBridge pickup250k250k47nFblackwhiteredgreenbareblackwhiteredgreenbareblackwhiteredgreenbareT1T2T3T4T5T6T7T8lug1lug2lug3tipsleevegroundlug1lug2lug3abNeck pickupMiddle pickupBridge pickup5-Way SwitchVolume 250kOutput JackGround wire to bridgeTone 250k.047 µF tone cap

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck pickupSource: Everything Axe neck pickup—Seymour Duncan Everything Axe NeckAs specified
Middle pickupSource: Everything Axe middle pickup—Seymour Duncan Everything Axe MiddleAs specified
Bridge pickupSource: Everything Axe bridge pickup—Seymour Duncan Everything Axe BridgeAs specified
5-Way SwitchSource: 5-way switch—Oak Grigsby 5-WayExample part
Volume 250k250kCTS 250k Audio PotExample part
Output Jack—Switchcraft #11Example part
Ground wire to bridge—Bridge ground wireGeneric
Tone 250k250kCTS 250k Audio PotExample part
.047 µF tone capSource: .047 cap47nFOrange Drop .047µFExample part

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck greenVolume casingTo a pot casinggreen
2Neck bareVolume casingTo a pot casingbare
3Middle greenVolume casingTo a pot casinggreen
4Middle bareVolume casingTo a pot casingbare
5Bridge greenVolume casingTo a pot casinggreen
6Bridge bareVolume casingTo a pot casingbare
7Ground wire to bridgeVolume casingTo a pot casingblack
8Volume bottom lugVolume casingLug bent onto the lower solder spot.To a pot casing
9Volume casingJack sleeveWireblack
10Middle whiteVolume casingDrawn with the middle green and bare into the upper solder spot.To a pot casingwhite
11.047 capTone casingTo a pot casing
12Tone casingVolume casing (lower solder spot)To a pot casingblack
13Bridge blackSwitch wired row, top lugWireblack
14Middle blackSwitch wired row, second lugRuns beside the middle red ('middle black & red').Wireblack
15Neck blackSwitch wired row, third lugWireblack
16Switch common (wired row, bottom lug)Switch opposite row, top lugSoldered at that lug on its way to the volume.Wireblack
17Switch opposite row, top lugVolume input lugWireblack
18Middle redSwitch wired row, second lugRuns beside the middle black ('middle black & red').Wirered
19Neck redNeck whiteSoldered together and taped off.Joined and insulatedred
20Bridge redBridge whiteSoldered together and taped off.Joined and insulatedred
21Volume middle lugJack tipHops over the tone-ground and sleeve wires.Wireblack
22Volume input lugTone first lugWireblack
23Tone middle lug.047 capWire

What each position does

SettingThe sourceEngine result
Bridge—Bridge pickup (both coils).
Bridge + middle—Middle pickup (coils in parallel) and Bridge pickup (both coils) in parallel.
Middle—Middle pickup (coils in parallel).
Middle + neck—Neck pickup (both coils) and Middle pickup (coils in parallel) in parallel.
Neck—Neck pickup (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Hum cancelling and phase follow the pickups' lead colours and coil polarity as Seymour Duncan publishes them; nothing here is measured.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • In each switch position, the meter across the jack should read the selected pickup, or two in parallel in positions 2 and 4.
  • With the volume at zero, tip and sleeve should read as a short.
  • The neck and bridge taped red–white joints should read about one coil's resistance to ground, roughly half the pickup's total (a few kΩ): not open, and not zero.
  • Turning the tone down should load the selected pickup through the .047 µF capacitor.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.