Parts and values
| In the drawing | Value | Part |
|---|---|---|
| Neck Blackout | — | Blackouts AHB-1 Neck |
| Bridge Blackout | — | Blackouts AHB-1 Bridge |
| Neck volume 25K | 25k | EMG 25K Pot |
| Bridge volume 25K | 25k | EMG 25K Pot |
| 3-way toggle | — | Switchcraft 3-Way Toggle |
| Stereo output jack | — | Switchcraft #12B |
| 9V battery clip | — | 9V Battery Clip |
| Bridge ground | — | Bridge ground wire |
| Bridge tone 25K | 25k | EMG 25K Pot |
| Neck tone 25K | 25k | EMG 25K Pot |
| Bridge .47 cap | 470nF | 0.47 µF Film Capacitor |
| Neck .47 cap | 470nF | 0.47 µF Film Capacitor |
Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.
Understand this wiring
- Seymour Duncan humbucker wire colors
See the pickup, recognise its two halves, and learn where each coloured wire goes.
Connections
In soldering order: grounds first, then the switch, the pickups and the signal path.
| # | From | To | How |
|---|---|---|---|
| 1 | Neck Blackout gnd | Neck volume 25K casing | Wire |
| 2 | Bridge Blackout gnd | Bridge volume 25K casing | Wire |
| 3 | 3-way toggle T4 | Bridge tone 25K casing | Wire |
| 4 | Neck volume 25K lug1 | Neck volume 25K casing | Wire |
| 5 | Bridge volume 25K lug1 | Bridge volume 25K casing | Wire |
| 6 | Neck volume 25K casing | Bridge volume 25K casing | Wire |
| 7 | Neck volume 25K casing | Neck tone 25K casing | Wire |
| 8 | Bridge tone 25K casing | Bridge volume 25K casing | Wire |
| 9 | Neck .47 cap b | Neck tone 25K casing | Wire |
| 10 | Bridge .47 cap b | Bridge tone 25K casing | Wire |
| 11 | Neck tone 25K casing | Stereo output jack sleeve | Wire |
| 12 | Bridge ground ground | Bridge tone 25K casing | Wire |
| 13 | Neck volume 25K lug2 | 3-way toggle T1 | Wire |
| 14 | Bridge volume 25K lug2 | 3-way toggle T2 | Wire |
| 15 | 3-way toggle T3 | Stereo output jack tip | Wire |
| 16 | Neck Blackout hot | Neck volume 25K lug3 | Wire |
| 17 | Bridge Blackout hot | Bridge volume 25K lug3 | Wire |
| 18 | Neck Blackout vplus | 9V battery clip vplus | Wire |
| 19 | Bridge Blackout vplus | 9V battery clip vplus | Wire |
| 20 | 9V battery clip vminus | Stereo output jack ring | Wire |
| 21 | Neck volume 25K lug3 | Neck tone 25K lug1 | Wire |
| 22 | Bridge volume 25K lug3 | Bridge tone 25K lug1 | Wire |
| 23 | Neck tone 25K lug2 | Neck .47 cap a | Wire |
| 24 | Bridge tone 25K lug2 | Bridge .47 cap a | Wire |
What each position does
| Setting | The source | Engine result |
|---|---|---|
| Neck | Passive simulation is not applied to active pickups; wiring topology only. | No pickup reaches the output. |
| Neck and bridge | Passive simulation is not applied to active pickups; wiring topology only. | No pickup reaches the output. |
| Bridge | Passive simulation is not applied to active pickups; wiring topology only. | No pickup reaches the output. |
Not simulated: this circuit is drawn for reference only.
- Active pickup gain and frequency response are not simulated.
- The catalog active buffer is approximated with the Blackouts Active Humbucker's terminals.
Before you solder
Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .
Check before plugging in
Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.