Skip to content
Tinkercaster

Tonerider wiring

Humbucker and two single coils: five-way auto-split, one volume, two tones

1 humbucker + 2 single coils · 5-way blade · 1V · 2T · auto-split in position 2

Tonerider sheet: neck and middle single coils and a four-conductor bridge humbucker on a five-way blade. The humbucker auto-splits in position 2 through the blade's second wafer. One 250k volume, 250k neck and mid tones, one .022 µF capacitor. No mini-toggle.

Viewed from the back of the controls, as you solder them.

Humbucker and two single coils: five-way auto-split, one volume, two tonesHumbucker and two single coils: five-way auto-split, one volume, two tones: 1 humbucker + 2 single coils · 5-way blade · 1V · 2T · auto-split in position 2. Original Tinkercaster drawing with labelled terminals.Neck pickupMid pickupBridge humbucker250k250k250k22nFwhiteblackyellowblackredblackwhitegreenbareT1T2T3T4T5T6T7T8lug1lug2lug3lug1lug2lug3lug1lug2lug3abtipsleevegroundNeck pickupMid pickupBridge humbucker5-way switchVolume 250kNeck Tone 250kMid Tone 250kTone capacitor (.022µF)Output jackFrom Bridge Ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck pickupSource: Neck single coil—Tonerider City Limits NeckExample partSame wiring for Tonerider Pure Vintage Neck
Mid pickupSource: Middle single coil—Tonerider City Limits MiddleExample partSame wiring for Tonerider Pure Vintage Middle
Bridge humbuckerSource: Bridge humbucker (4-conductor)—Tonerider Alnico 2 ClassicExample partSame wiring for Tonerider Alnico 4 Classic, Tonerider Rocksong
5-way switchSource: 5-way blade—Oak Grigsby 5-WayExample part
Volume 250k250kCTS 250k Audio PotExample part
Neck Tone 250k250kCTS 250k Audio PotExample part
Mid Tone 250k250kCTS 250k Audio PotExample part
Tone capacitor (.022µF)Source: Orange capacitor .022µF22nFOrange Drop .022µFExample part
Output jack—Switchcraft #11Example part
From Bridge Ground—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Bridge humbucker gnd (green)Volume 250k casingWiregreen
2Bridge humbucker bareVolume 250k casingWirebare
3Neck single gnd (black)Volume 250k casingWireblack
4Middle single gnd (black)Volume 250k casingWireblack
5Volume 250k lug1Volume 250k casingWireground
6Volume 250k casingOutput jack sleeveWireblack
7From Bridge GroundVolume 250k casingWireblack
8Volume 250k casingNeck Tone 250k casingWireblack
9Mid Tone 250k lug2.022µF leg aWirebare
10.022µF leg aNeck Tone 250k lug1Wirebare
11.022µF leg bNeck Tone 250k casingWireblack
12Neck Tone 250k casingMid Tone 250k casingWireblack
135-Way Switch T5Volume 250k casingThe second pole's middle lug is grounded; its common is left unwired, so the humbucker's link on T7 meets ground only in position 2, where the blade bridges T7 and T5.Wireblack
14Bridge humbucker black5-Way Switch T7 (split contact)Wireblack
15Bridge humbucker white5-Way Switch T7 (split contact)Black and white meet on the switch's split contact, as drawn.Wirewhite
16Bridge humbucker hot (red)5-Way Switch T3Wirered
17Middle single hot (yellow)5-Way Switch T1Wireyellow
18Neck single hot (white)5-Way Switch T2Wirewhite
195-Way Switch T4Volume 250k lug3Wirewhite
205-Way Switch T1Mid Tone 250k lug1Wireblack
215-Way Switch T2Neck Tone 250k lug2Wireblack
22Volume 250k lug2Output jack tipWirewhite

What each position does

SettingThe sourceEngine result
Bridge humbuckerSheet: auto-split in position 2 only; in position 1 the link's lug touches only the unwired common.Bridge humbucker (both coils).
Bridge humbucker split + midAuto-split: one humbucker coil in parallel with the middle single coil.Mid pickup and Bridge humbucker (split to one coil) in parallel.
MiddleMiddle single coil in circuit.Mid pickup.
Middle + neckNeck and middle single coils in parallel.Neck pickup and Mid pickup in parallel.
NeckNeck single coil in circuit.Neck pickup.

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The capacitor value is printed as .022µF on the sheet.
  • Pot tapers are not printed; pots are simulated with a linear track.
  • Tone network is taken from the Apex auto-split reference for this layout; not measured.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.