Skip to content
Tinkercaster

Tonerider wiring

HSS five-way auto-split volume and tone

Viewed from the back of the controls, as you solder them.

HSS five-way auto-split volume and toneHSS five-way auto-split volume and tone: HSS five-way auto-split volume and tone. Original Tinkercaster drawing with labelled terminals.Neck pickupMid pickupBridge humbucker250k250k22nFwhiteblackyellowblackredblackwhitegreenbareT1T2T3T4T5T6T7T8lug1lug2lug3lug1lug2lug3abtipsleevegroundNeck pickupMid pickupBridge humbucker5-way bladeVolume 250kTone 250k.022µfOutput jackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck pickup—Tonerider City Limits NeckExample partSame wiring for Tonerider Pure Vintage Neck
Mid pickup—Tonerider City Limits MiddleExample partSame wiring for Tonerider Pure Vintage Middle
Bridge humbucker—Tonerider Alnico 2 ClassicExample partSame wiring for Tonerider Alnico 4 Classic, Tonerider Rocksong
5-way blade—Oak Grigsby 5-WayExample part
Volume 250k250kCTS 250k Audio PotExample part
Tone 250k250kCTS 250k Audio PotExample part
.022µf22nFOrange Drop .022µFExample part
Output jack—Switchcraft #11Example part
Bridge ground—Bridge ground wireExample part

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Bridge humbucker gndVolume 250k casingWiregreen
2Bridge humbucker bareVolume 250k casingWirebare
3Neck pickup gndVolume 250k casingWireblack
4Mid pickup gndVolume 250k casingWireblack
55-way blade T5Volume 250k casingWireblack
6Volume 250k lug1Volume 250k casingWireground
7Volume 250k casingOutput jack sleeveWireblack
8Bridge ground groundVolume 250k casingWireblack
9Tone 250k lug2.022µf aWirebare
10.022µf bTone 250k casingWirebare
11Tone 250k casingVolume 250k casingWireblack
12Bridge humbucker hot5-way blade T3Wirered
13Mid pickup hot5-way blade T1Wireyellow
14Neck pickup hot5-way blade T2Wirewhite
155-way blade T4Volume 250k lug3Wireblack
16Bridge humbucker black5-way blade T7Wireblack
17Bridge humbucker blackBridge humbucker whiteWireblack
18Volume 250k lug2Output jack tipWirewhite
19Volume 250k lug3Tone 250k lug1Wireblack

What each position does

SettingThe sourceEngine result
Position 1Engine reading of the transcribed board; matches the source legend.Bridge humbucker (both coils).
Position 2Engine reading of the transcribed board; matches the source legend.Mid pickup and Bridge humbucker (split to one coil) in parallel.
Position 3Engine reading of the transcribed board; matches the source legend.Mid pickup.
Position 4Engine reading of the transcribed board; matches the source legend.Neck pickup and Mid pickup in parallel.
Position 5Engine reading of the transcribed board; matches the source legend.Neck pickup.

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Custom tapers are not reproduced; pots are simulated as linear.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.