Skip to content
Tinkercaster

DiMarzio wiring

Sixties P Plug-In with one volume and one tone

One P-Bass · No switch · One volume · One tone

DiMarzio Sixties P DP124 through a 500K custom-taper volume, a 250K custom-taper tone and a .033 µF capacitor, to a Switchcraft two-conductor jack.

Viewed from the back of the controls, as you solder them.

Sixties P Plug-In with one volume and one toneSixties P Plug-In with one volume and one tone: One P-Bass · No switch · One volume · One tone. Original Tinkercaster drawing with labelled terminals.Sixties P500k250k33nFwhiteblackblackwhitebarebarelug1lug2lug3lug1lug2lug3abtipsleevegroundSixties PVolume 500K custom taperTone 250K custom taper.033µFOutput jackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Sixties PSource: Sixties P Plug-In DP124—Sixties P™ Plug-InAs specified
Volume 500K custom taperSource: Volume 500K custom taper pot (EP1201)500kCTS 500k Audio PotExample part
Tone 250K custom taperSource: Tone 250K custom taper pot (EP1200)250kCTS 250k Audio PotExample part
.033µFSource: .033µF capacitor (EP1033)33nFOrange Drop .033µFExample part
Output jackSource: Switchcraft output jack, 2-conductor (EP1301)—Switchcraft #11Example part
Bridge groundSource: TO BRIDGE GROUND—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Pickup ground (second white lead)Volume casingTo a pot casing
2Volume ground lugVolume casingShort black link.To a pot casing
3.033µF capacitorTone casingTo a pot casing
4Tone casingVolume casingTo a pot casing
5Tone casingJack sleeveWire
6TO BRIDGE GROUNDJack sleeveShield or ground
7Sixties P bare shieldgroundShield or groundbare
8Sixties P second bare shieldgroundShield or groundbare
9Pickup hot (white)Volume input lugWirewhite
10Pickup black (first half)Pickup black (second half)Series link between the halves: join the two BLACK leads and insulate them, as the sheet shows.Joined and insulatedblack
11Volume middle lugJack tipWire
12Volume input lugTone middle lugWire
13Tone bottom lug.033µF capacitorWire

What it does

Engine result: Sixties P (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The P-Bass is drawn as the Sixties P; its split-coil and hum-cancelling construction is not modelled.
  • The source's custom-taper pots are not reproduced: both pots are simulated with a linear track, so settings between the knob ends are approximate.
  • Tone capacitor value matches the printed .033µF.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • With both pots up, the meter across the jack should read the pickup resistance.
  • The jack sleeve should read continuity to the volume casing, the tone casing and the bridge ground wire.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.