Skip to content
Tinkercaster

Seymour Duncan wiring

Two singles and a humbucker, five-way, volume and two tones

HSS · Five-way · One volume · Two tones (shared .047)

Transcribed from the manufacturer wiring sheet and checked against the engine.

Viewed from the back of the controls, as you solder them.

Two singles and a humbucker, five-way, volume and two tonesTwo singles and a humbucker, five-way, volume and two tones: HSS · Five-way · One volume · Two tones (shared .047). Original Tinkercaster drawing with labelled terminals.Neck pickupMiddle pickupBridge humbucker250k250k250k47nFwhiteblackwhiteblackblackgreenwhiteredbareT1T2T3T4T5T6T7T8lug1lug2lug3lug1lug2lug3lug1lug2lug3abtipsleevegroundNeck pickupMiddle pickupBridge humbucker5-Way Blade SwitchVolume · 250kTone 1 (neck) · 250kTone 2 (middle) · 250k.047 cap · 47nFOutput jackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck pickup—Vintage Staggered Strat SSL-1Example partSame wiring for Vintage Flat Strat SSL-2, Quarter-Pound Flat Strat SSL-4, Alnico II Pro Staggered Strat APS-1, Custom SSL-5
Middle pickup—Vintage Staggered Strat SSL-1Example partSame wiring for Vintage Flat Strat SSL-2, Quarter-Pound Flat Strat SSL-4, Alnico II Pro Staggered Strat APS-1, Custom SSL-5
Bridge humbucker—JB Model SH-4Example partSame wiring for Duncan Custom SH-5, Duncan Distortion SH-6 Bridge, Invader SH-8 Bridge, Seymour Duncan SH-2 Jazz Bridge, Seymour Duncan SH-3 Stag Mag, Custom Five SH-14
5-Way Blade Switch—Oak Grigsby 5-WayExample part
Volume250kNot on the sheet; stand-inCTS 250k Audio PotExample part
Tone 1 (neck)250kNot on the sheet; stand-inCTS 250k Audio PotExample part
Tone 2 (middle)250kNot on the sheet; stand-inCTS 250k Audio PotExample part
.047 cap47nFOrange Drop .047µFExample part
Output jack—Switchcraft #11Example part
Bridge ground—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1w2 as drawnw2 as drawnWiregreen
2w3 as drawnw3 as drawnWirebare
3w7 as drawnw7 as drawnWireblack
4w8 as drawnw8 as drawnWireblack
5w13 as drawnw13 as drawnWireground
6w15 as drawnw15 as drawnWireblack
7w16 as drawnw16 as drawnWireblack
8w18 as drawnw18 as drawnWireblack
9w20 as drawnw20 as drawnWireblack
10w21 as drawnw21 as drawnWireblack
11w4 as drawnw4 as drawnWireblack
12w5 as drawnw5 as drawnWirewhite
13w6 as drawnw6 as drawnWirewhite
14w9 as drawnw9 as drawnWireblack
15w10 as drawnw10 as drawnWireblack
165-Way Blade Switch T6Tone 1 (neck) lug1Wireblack
17w12 as drawnw12 as drawnWireblack
18w1 as drawnw1 as drawnWirered
19w14 as drawnw14 as drawnWireblack
20w17 as drawnw17 as drawnWireblack
21w19 as drawnw19 as drawnWireblack

What each position does

SettingThe sourceEngine result
BridgeEngine reading of the transcribed board; matches the source legend.Bridge humbucker (both coils).
Bridge + middleEngine reading of the transcribed board; matches the source legend.Middle pickup and Bridge humbucker (both coils) in parallel.
MiddleEngine reading of the transcribed board; matches the source legend.Middle pickup.
Middle + neckEngine reading of the transcribed board; matches the source legend.Neck pickup and Middle pickup in parallel.
NeckEngine reading of the transcribed board; matches the source legend.Neck pickup.

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Pot values are not printed on the source; 250k audio-taper stand-ins matching common Strat practice are used and treated as linear by the simulator.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.