Parts and values
| In the drawing | Value | Part |
|---|---|---|
| Neck pickup | — | Little '59 SL59-1 Neck (Strat-size) |
| Middle Strat stack | — | Strat Stack Plus |
| Bridge pickup | — | Little '59 SL59-1 Bridge (Strat-size) |
| 5-Way Blade Switch | — | Oak Grigsby 5-Way |
| Volume 250k | 250k | CTS 250k Audio Pot |
| Tone 1 (neck) | 250k | CTS 250k Audio Pot |
| Tone 2 (middle) | 250k | CTS 250k Audio Pot |
| .022 cap | 22nF | Orange Drop .022µF |
| Output jack | — | Switchcraft #11 |
| Bridge ground | — | Bridge ground wire |
Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.
Understand this wiring
- Seymour Duncan humbucker wire colors
See the pickup, recognise its two halves, and learn where each coloured wire goes.
Connections
In soldering order: grounds first, then the switch, the pickups and the signal path.
| # | From | To | How |
|---|---|---|---|
| 1 | Neck pickup gnd | Volume 250k casing | Wire |
| 2 | Neck pickup bare | Volume 250k casing | Wire |
| 3 | Middle Strat Stack Plus gnd | Volume 250k casing | Wire |
| 4 | Middle Strat Stack Plus bare | Volume 250k casing | Wire |
| 5 | Bridge pickup gnd | Volume 250k casing | Wire |
| 6 | Bridge pickup bare | Volume 250k casing | Wire |
| 7 | Volume 250k lug1 | Volume 250k casing | Wire |
| 8 | Volume 250k casing | Output jack sleeve | Wire |
| 9 | Bridge ground ground | Volume 250k casing | Wire |
| 10 | .022 cap b | Tone 1 (neck) casing | Wire |
| 11 | Tone 1 (neck) casing | Volume 250k casing | Wire |
| 12 | Tone 2 (middle) casing | Tone 1 (neck) casing | Wire |
| 13 | Bridge pickup hot | 5-Way Blade Switch T3 | Wire |
| 14 | Middle Strat Stack Plus hot | 5-Way Blade Switch T1 | Wire |
| 15 | Neck pickup hot | 5-Way Blade Switch T2 | Wire |
| 16 | 5-Way Blade Switch T4 | 5-Way Blade Switch T8 | Wire |
| 17 | 5-Way Blade Switch T8 | Volume 250k lug3 | Wire |
| 18 | 5-Way Blade Switch T6 | Tone 1 (neck) lug1 | Wire |
| 19 | 5-Way Blade Switch T5 | Tone 2 (middle) lug1 | Wire |
| 20 | Neck pickup white | Neck pickup red | Wire |
| 21 | Bridge pickup white | Bridge pickup red | Wire |
| 22 | Volume 250k lug2 | Output jack tip | Wire |
| 23 | Tone 1 (neck) lug2 | .022 cap a | Wire |
| 24 | Tone 2 (middle) lug2 | Tone 1 (neck) lug2 | Wire |
| 25 | Middle Strat Stack Plus black | Middle Strat Stack Plus white | Wire |
What each position does
| Setting | The source | Engine result |
|---|---|---|
| Bridge | Engine reading of the transcribed board. | Bridge pickup (both coils). |
| Bridge + middle | Engine reading of the transcribed board. | Middle Strat stack (both coils) and Bridge pickup (both coils) in parallel. |
| Middle | Engine reading of the transcribed board. | Middle Strat stack (both coils). |
| Middle + neck | Engine reading of the transcribed board. | Neck pickup (both coils) and Middle Strat stack (both coils) in parallel. |
| Neck | Engine reading of the transcribed board. | Neck pickup (both coils). |
Checked with the Tinkercaster wiring engine against the switching the source describes.
- Two Strat tones share one capacitor via a jumper; toneReachesSignal may fail.
- Strat Stack Plus on middle pickup.
Before you solder
Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .
Check before plugging in
Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.