Skip to content
Tinkercaster

Seymour Duncan wiring

Telecaster two Tele humbuckers, four-way

Two Tele humbuckers · Four-way blade · One volume · One tone

Two Seymour Duncan Tele humbuckers on a four-way blade, one 250k volume and one 250k tone with a .047 µF capacitor. Position 4 runs both pickups in series.

Viewed from the back of the controls, as you solder them.

Telecaster two Tele humbuckers, four-wayTelecaster two Tele humbuckers, four-way: Two Tele humbuckers · Four-way blade · One volume · One tone. Original Tinkercaster drawing with labelled terminals.Neck Tele humbuckerBridge Tele humbucker250k250k47nFblackgreenwhiteredbareblackgreenwhiteredbareT1T2T3T4T5T6T7T8T9T10lug1lug2lug3lug1lug2lug3abtipsleevegroundNeck Tele humbuckerBridge Tele humbucker4-Way SwitchVolume 250kTone 250k.047 cap · 47nFOutput JackGround wire from bridge

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck Tele humbucker—Jazz Model SH-2 NeckExample partSame wiring for '59 Model SH-1 Neck, Seymour Duncan Antiquity Neck, Pearly Gates SH-PG1 Neck, Invader SH-8 Neck, Duncan Distortion SH-6 Neck, Alnico II Pro APH-1 Neck
Bridge Tele humbucker—JB Model SH-4Example partSame wiring for Duncan Distortion SH-6 Bridge, Invader SH-8 Bridge, Duncan Custom SH-5, Seymour Duncan SH-3 Stag Mag, Seymour Duncan SH-11 Custom Custom, Seymour Duncan SH-2 Jazz Bridge
4-Way Switch—4-Way Tele Mod SwitchExample part
Volume 250k250kCTS 250k Audio PotExample part
Tone 250k250kCTS 250k Audio PotExample part
.047 cap47nFOrange Drop .047µFExample part
Output Jack—Switchcraft #11Example part
Ground wire from bridge—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck Tele humbucker gnd4-Way Switch T5Wiregreen
2Neck Tele humbucker bareVolume 250k casingWirebare
3Bridge Tele humbucker gndVolume 250k casingWiregreen
4Bridge Tele humbucker bareVolume 250k casingWirebare
54-Way Switch T3Volume 250k casingWireblack
6Ground wire from bridge groundVolume 250k casingWireblack
7Volume 250k lug1Volume 250k casingWireground
8.047 cap bTone 250k casingWireblack
9Volume 250k casingTone 250k casingWireblack
10Tone 250k casingOutput Jack sleeveWireblack
11Neck Tele humbucker hot4-Way Switch T6Wireblack
12Bridge Tele humbucker hot4-Way Switch T10Wireblack
134-Way Switch T24-Way Switch T3Wireblack
144-Way Switch T64-Way Switch T7Wireblack
154-Way Switch T7Volume 250k lug3Wireblack
164-Way Switch T44-Way Switch T9Wireblack
17Neck Tele humbucker redNeck Tele humbucker whiteWirered
18Bridge Tele humbucker whiteBridge Tele humbucker redWirered
19Volume 250k lug2Output Jack tipWireblack
20Volume 250k lug3Tone 250k lug1Wireblack
21Tone 250k lug2.047 cap aWireblack

What each position does

SettingThe sourceEngine result
Bridge1. bridge pickupBridge Tele humbucker (both coils).
Bridge and neck in parallel2. bridge & neck pickups parallelNeck Tele humbucker (both coils) and Bridge Tele humbucker (both coils) in parallel.
Neck3. neck pickupNeck Tele humbucker (both coils).
Bridge and neck in series4. bridge & neck in series (higher output and beefier tone)Neck Tele humbucker (both coils) and Bridge Tele humbucker (both coils) in series.

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.