Parts and values
| In the drawing | Value | Part |
|---|---|---|
| Neck pickup | — | Little '59 SL59-1 Neck (Strat-size) |
| Middle pickup | — | Little '59 SL59-1 Neck (Strat-size) |
| Bridge pickup | — | JB Jr. SJBJ-1 Bridge (Strat-size) |
| 5-Way Switch | — | Oak Grigsby 5-Way |
| Volume 250k | 250k | CTS 250k Audio Pot |
| Output Jack | — | Switchcraft #11 |
| Ground wire to bridge | — | Bridge ground wire |
Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.
Understand this wiring
- Seymour Duncan humbucker wire colors
See the pickup, recognise its two halves, and learn where each coloured wire goes.
Connections
In soldering order: grounds first, then the switch, the pickups and the signal path.
| # | From | To | How |
|---|---|---|---|
| 1 | Neck green | Volume casing | To a pot casing |
| 2 | Neck bare | Volume casing | To a pot casing |
| 3 | Middle green | Volume casing | To a pot casing |
| 4 | Middle bare | Volume casing | To a pot casing |
| 5 | Bridge green | Volume casing | To a pot casing |
| 6 | Bridge bare | Volume casing | To a pot casing |
| 7 | Ground wire to bridge | Volume casing | To a pot casing |
| 8 | Volume bottom lug | Volume casing | To a pot casing |
| 9 | Volume casing | Jack sleeve | Wire |
| 10 | Bridge black | Switch wired row, top lug | Wire |
| 11 | Middle black | Switch wired row, second lug | Wire |
| 12 | Neck black | Switch wired row, third lug | Wire |
| 13 | Switch common (wired row, bottom lug) | Switch opposite row, top lug | Wire |
| 14 | Switch opposite row, top lug | Volume input lug | Wire |
| 15 | Neck red | Neck white | Joined and insulated |
| 16 | Middle red | Middle white | Joined and insulated |
| 17 | Bridge red | Bridge white | Joined and insulated |
| 18 | Volume middle lug | Jack tip | Wire |
What each position does
| Setting | The source | Engine result |
|---|---|---|
| Bridge | — | Bridge pickup (both coils). |
| Bridge + middle | — | Middle pickup (both coils) and Bridge pickup (both coils) in parallel. |
| Middle | — | Middle pickup (both coils). |
| Middle + neck | — | Neck pickup (both coils) and Middle pickup (both coils) in parallel. |
| Neck | — | Neck pickup (both coils). |
Checked with the Tinkercaster wiring engine against the switching the source describes.
- Hum cancelling and phase follow the pickups' lead colours and coil polarity as Seymour Duncan publishes them; nothing here is measured.
- Pickup resistance is not specified, so no numeric meter readings are given.
Before you solder
Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .
Check before plugging in
- In each switch position, the meter across the jack should read the selected pickup, or two in parallel in positions 2 and 4.
- With the volume at zero, tip and sleeve should read as a short.
- Each taped red–white joint should read about one coil's resistance to ground, roughly half the pickup's total (a few kΩ): not open, and not zero.
Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.