Skip to content
Tinkercaster

Seymour Duncan wiring

Three Strat Stack Plus pickups, five-way, volume

3 Strat Stack Plus · 5-way · 1V

Transcribed from the manufacturer wiring sheet.

Viewed from the back of the controls, as you solder them.

Three Strat Stack Plus pickups, five-way, volumeThree Strat Stack Plus pickups, five-way, volume: 3 Strat Stack Plus · 5-way · 1V. Original Tinkercaster drawing with labelled terminals.Neck stackMiddle stackBridge stack250kwhiteredblackbarewhiteredblackbarewhiteredblackbareT1T2T3T4T5T6T7T8lug1lug2lug3tipsleevegroundNeck stackMiddle stackBridge stack5-Way SwitchVolume 250kOutput JackGround wire to bridge

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck stack—Strat Stack PlusAs specifiedSame wiring for Strat Stack Plus
Middle stack—Strat Stack PlusAs specifiedSame wiring for Strat Stack Plus
Bridge stack—Strat Stack PlusAs specifiedSame wiring for Strat Stack Plus
5-Way Switch—Oak Grigsby 5-WayExample part
Volume 250k250kCTS 250k Audio PotExample part
Output Jack—Switchcraft #11Example part
Ground wire to bridge—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck stack gndVolume 250k casingRed leads on all three stacks are taped off on the sheet, so they get no wire.Wireblack
2Neck stack bareVolume 250k casingWirebare
3Middle stack gndVolume 250k casingWireblack
4Middle stack bareVolume 250k casingWirebare
5Bridge stack gndVolume 250k casingWireblack
6Bridge stack bareVolume 250k casingWirebare
7Ground wire to bridge groundVolume 250k casingWireblack
8Volume 250k lug1Volume 250k casingWireground
9Volume 250k casingOutput Jack sleeveWireblack
10Bridge stack hot5-Way Switch T3Wirewhite
11Middle stack hot5-Way Switch T1Wirewhite
12Neck stack hot5-Way Switch T2Wirewhite
135-Way Switch T45-Way Switch T8Wireblack
145-Way Switch T8Volume 250k lug3Wireblack
15Volume 250k lug2Output Jack tipWireblack

What each position does

SettingThe sourceEngine result
BridgeEngine reading of the transcribed board.Bridge stack (both coils).
Bridge + middleEngine reading of the transcribed board.Middle stack (both coils) and Bridge stack (both coils) in parallel.
MiddleEngine reading of the transcribed board.Middle stack (both coils).
Middle + neckEngine reading of the transcribed board.Neck stack (both coils) and Middle stack (both coils) in parallel.
NeckEngine reading of the transcribed board.Neck stack (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Stacked pickup construction is not modelled beyond the transcribed lug map.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.