Skip to content
Tinkercaster

Seymour Duncan wiring

Two humbuckers, toggle, series/parallel and phase push/pulls

HH · 3-way toggle · Master volume 500k · Neck tone 500k push/pull series/parallel · Bridge tone 500k push/pull phase

Seymour Duncan sheet: two humbuckers on a 3-way toggle with a 500k master volume and two 500k tones with .047 caps. The bridge tone's push/pull reverses the bridge pickup's black and green (phase); the neck tone's push/pull either grounds the neck green and sends the bridge signal to the toggle (parallel) or joins the bridge signal to the neck green (series). Both humbuckers' red & white are soldered together and taped off.

Viewed from the back of the controls, as you solder them.

Two humbuckers, toggle, series/parallel and phase push/pullsTwo humbuckers, toggle, series/parallel and phase push/pulls: HH · 3-way toggle · Master volume 500k · Neck tone 500k push/pull series/parallel · Bridge tone 500k push/pull phase. Original Tinkercaster drawing with labelled terminals.Neck PickupBridge Pickup500k500k500k47nF47nFblackgreenwhiteredbareblackgreenwhiteredbareT1T2T3T4lug1lug2lug3lug1lug2lug3sw1sw2sw3sw4sw5sw6tipsleevelug1lug2lug3sw1sw2sw3sw4sw5sw6groundababNeck PickupBridge Pickup3-Way ToggleMaster Volume 500kNeck Tone 500k series/parallelOutput JackBridge Tone 500k phaseBridge ground wireNeck tone .047 cap · 47nFBridge tone .047 cap · 47nF

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck Pickup—'59 Model SH-1 NeckExample partSame wiring for Jazz Model SH-2 Neck, Duncan Distortion SH-6 Neck, Invader SH-8 Neck, Seymour Duncan Antiquity Neck, Alnico II Pro APH-1 Neck, Pearly Gates SH-PG1 Neck
Bridge Pickup—JB Model SH-4Example partSame wiring for '59 Model SH-1 Bridge, Duncan Custom SH-5, Duncan Distortion SH-6 Bridge, Invader SH-8 Bridge, Custom Five SH-14, Seymour Duncan SH-2 Jazz Bridge
3-Way Toggle—Switchcraft 3-Way ToggleExample part
Master Volume 500k500kCTS 500k Audio PotExample part
Neck Tone 500k series/parallel500k500k Push-Pull DPDTExample part
Output Jack—Switchcraft #11Example part
Bridge Tone 500k phase500k500k Push-Pull DPDTExample part
Bridge ground wire—Bridge ground wireGeneric
Neck tone .047 cap47nFOrange Drop .047µFExample part
Bridge tone .047 cap47nFOrange Drop .047µFExample part

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck greenNeck tone push/pull right middle lugWiregreen
2Neck bareVolume casing (lower Solder spot)Shield or groundbare
3Bridge greenBridge tone push/pull right middle lugWiregreen
4Bridge bareVolume casing (upper Solder spot)Shield or groundbare
5Bridge tone push/pull bottom-left lugBridge tone casing (Solder spot)To a pot casingblack
6Bridge tone .047 capBridge tone casing (Solder spot)To a pot casing
7Neck tone push/pull top-right lugNeck tone casing (Solder spot)To a pot casingblack
8Neck tone .047 capNeck tone casing (Solder spot)To a pot casing
9Toggle frame lugVolume casing (upper Solder spot)To a pot casingblack
10Volume third lugVolume casingLug bent onto the casing.To a pot casing
11Volume casing (upper Solder spot)Bridge tone casing (Solder spot)Hops over the bridge black.To a pot casingblack
12Bridge tone casing (Solder spot)Neck tone casing (Solder spot)To a pot casingblack
13Neck tone casing (Solder spot)Jack SleeveWireblack
14Bridge ground wireBridge tone casing (Solder spot)To a pot casingblack
15Neck blackToggle first outer lugWireblack
16Neck tone push/pull top-left lugToggle other outer lugHops over the neck green.Wireblack
17Toggle first outer lugNeck tone first lugHops over the neck green.Wireblack
18Toggle middle lugVolume first lugWireblack
19Neck redNeck whiteSoldered together and taped off.Joined and insulatedred
20Bridge redBridge whiteSoldered together and taped off.Joined and insulatedred
21Bridge blackBridge tone push/pull left middle lugWireblack
22Bridge tone push/pull top-left lugBridge tone push/pull bottom-right lugCross jumper.Wireblack
23Bridge tone push/pull top-right lugBridge tone push/pull bottom-left lugCross jumper, drawn continuing to the Solder spot.Wireblack
24Bridge tone push/pull top-left lugNeck tone push/pull left middle lugHops over the bridge green and the pot wiring.Wireblack
25Bridge tone push/pull top-left lugBridge tone first lugWireblack
26Bridge tone middle lugBridge tone .047 capWireblack
27Neck tone push/pull bottom-left lugNeck tone push/pull bottom-right lugJumper.Wireblack
28Neck tone middle lugNeck tone .047 capWireblack
29Volume middle lugJack TipHops over the ground wires.Wireblack

What each position does

SettingThe sourceEngine result
Neck, neck tone pushed (parallel), bridge tone pushed (in phase)No knob legend printed; pull is taken as series (neck tone) and out of phase (bridge tone).Neck Pickup (both coils).
Both, neck tone pushed (parallel), bridge tone pushed (in phase)No knob legend printed; pull is taken as series (neck tone) and out of phase (bridge tone).Neck Pickup (both coils) and Bridge Pickup (both coils) in parallel.
Bridge, neck tone pushed (parallel), bridge tone pushed (in phase)No knob legend printed; pull is taken as series (neck tone) and out of phase (bridge tone).Bridge Pickup (both coils).
Neck, neck tone pushed (parallel), bridge tone pulled (out of phase)No knob legend printed; pull is taken as series (neck tone) and out of phase (bridge tone). Phase pulled: the bridge pickup's black and green are reversed.Neck Pickup (both coils).
Both, neck tone pushed (parallel), bridge tone pulled (out of phase)No knob legend printed; pull is taken as series (neck tone) and out of phase (bridge tone). Phase pulled: the bridge pickup's black and green are reversed.Neck Pickup (both coils) and Bridge Pickup (both coils) in parallel.
Bridge, neck tone pushed (parallel), bridge tone pulled (out of phase)No knob legend printed; pull is taken as series (neck tone) and out of phase (bridge tone). Phase pulled: the bridge pickup's black and green are reversed. On its own this is not audible.Bridge Pickup (both coils).
Neck, neck tone pulled (series), bridge tone pushed (in phase)No knob legend printed; pull is taken as series (neck tone) and out of phase (bridge tone). Series: the bridge signal feeds the neck green, so both play in series.Neck Pickup (both coils) and Bridge Pickup (both coils) in series.
Both, neck tone pulled (series), bridge tone pushed (in phase)No knob legend printed; pull is taken as series (neck tone) and out of phase (bridge tone). Series: the bridge signal feeds the neck green, so both play in series.Neck Pickup (both coils) and Bridge Pickup (both coils) in series.
Bridge, neck tone pulled (series), bridge tone pushed (in phase)No knob legend printed; pull is taken as series (neck tone) and out of phase (bridge tone). Series: the bridge signal is moved off the toggle's bridge lug, so this position is silent.No pickup reaches the output.
Neck, neck tone pulled (series), bridge tone pulled (out of phase)No knob legend printed; pull is taken as series (neck tone) and out of phase (bridge tone). Series: the bridge signal feeds the neck green, so both play in series. Phase pulled: the bridge pickup's black and green are reversed.Neck Pickup (both coils) and Bridge Pickup (both coils) in series.
Both, neck tone pulled (series), bridge tone pulled (out of phase)No knob legend printed; pull is taken as series (neck tone) and out of phase (bridge tone). Series: the bridge signal feeds the neck green, so both play in series. Phase pulled: the bridge pickup's black and green are reversed.Neck Pickup (both coils) and Bridge Pickup (both coils) in series.
Bridge, neck tone pulled (series), bridge tone pulled (out of phase)No knob legend printed; pull is taken as series (neck tone) and out of phase (bridge tone). Series: the bridge signal is moved off the toggle's bridge lug, so this position is silent.No pickup reaches the output.

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The sheet does not say which knob position is series or out of phase; the usual push/pull behaviour is assumed (pulled = series, out of phase).
  • The engine does not report phase; the phase states record it in their notes and list the same pickups as in phase.
  • Hum cancelling and phase follow the pickups' lead colours and coil polarity as Seymour Duncan publishes them; pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • Both knobs pushed: the toggle gives neck, both in parallel and bridge.
  • Neck tone pulled: toggle positions 1 and 2 read both humbuckers in series; position 3 reads open.
  • Bridge tone pulled with both pickups on: the output thins (out of phase).

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.