Skip to content
Tinkercaster

Seymour Duncan wiring

Two stacks and SCH, five-way, volume and tone

2 stacks · SCH · 5-way · 1V · 1T

Seymour Duncan sheet: Strat Stack Plus pickups in the neck and middle and a single coil sized humbucker in the bridge on a 5-way blade with a 250k master volume, a 250k tone and a .047 cap. The humbuckers' red & white are taped off and each Strat Stack Plus red is taped off, so every pickup runs full; the blade gives bridge, bridge + middle, middle, middle + neck and neck.

Viewed from the back of the controls, as you solder them.

Two stacks and SCH, five-way, volume and toneTwo stacks and SCH, five-way, volume and tone: 2 stacks · SCH · 5-way · 1V · 1T. Original Tinkercaster drawing with labelled terminals.Neck Strat Stack PlusMiddle Strat Stack PlusBridge single coil sized humbucker250k250k47nFwhiteredblackbarewhiteredblackbareblackgreenwhiteredbareT1T2T3T4T5T6T7T8lug1lug2lug3lug1lug2lug3abtipsleevegroundNeck Strat Stack PlusMiddle Strat Stack PlusBridge single coil sized humbucker5-Way SwitchVolume 250kTone 250k.047 µF tone capOutput JackGround wire to bridge

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck Strat Stack Plus—Strat Stack PlusExample part
Middle Strat Stack Plus—Strat Stack PlusExample part
Bridge single coil sized humbucker—Little '59 SL59-1 Bridge (Strat-size)Example partSame wiring for JB Jr. SJBJ-1 Bridge (Strat-size), Hot Rails SHR-1 Bridge (Strat-size)
5-Way SwitchSource: 5-way blade—Oak Grigsby 5-WayExample part
Volume 250kSource: Master volume 250k250kCTS 250k Audio PotExample part
Tone 250k250kCTS 250k Audio PotExample part
.047 µF tone capSource: .047 cap47nFOrange Drop .047µFExample part
Output Jack—Switchcraft #11Example part
Ground wire to bridge—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck Strat Stack Plus black (ground)Volume casing (upper Solder spot)To a pot casingblack
2Neck Strat Stack Plus drainVolume casing (upper Solder spot)Drawn gold.Shield or groundbare
3Middle Strat Stack Plus black (ground)Volume casing (upper Solder spot)To a pot casingblack
4Middle Strat Stack Plus drainVolume casing (upper Solder spot)Drawn gold.Shield or groundbare
5Bridge single coil sized humbucker green (ground)Volume casing (upper Solder spot)To a pot casinggreen
6Bridge single coil sized humbucker bareVolume casing (upper Solder spot)Drawn grey beside the green.Shield or groundbare
7Ground wire to bridgeVolume casingTo a pot casingblack
8Volume third lugVolume casingLug bent onto the casing under the lower Solder spot.To a pot casing
9Volume casing (upper Solder spot)Jack sleeveWireblack
10.047 capTone casing (Solder spot)To a pot casing
11Tone casing (Solder spot)Volume casing (lower Solder spot)To a pot casingblack
12Bridge single coil sized humbucker black (hot)Blade upper-left row, first lugLabelled 'bridge black' at the blade.Wireblack
13Middle Strat Stack Plus white (hot)Blade upper-left row, second lugLabelled 'middle white' at the blade.Wirewhite
14Neck Strat Stack Plus white (hot)Blade upper-left row, third lugLabelled 'neck white' at the blade.Wirewhite
15Blade upper-left row, fourth lugBlade lower-right row, first lugJumper across the blade between the two commons.Wireblack
16Blade lower-right row, first lugVolume first lugWireblack
17Bridge single coil sized humbucker whiteBridge single coil sized humbucker redSoldered together and taped off ('Red & white wires get taped off').Joined and insulatedred
18Volume middle lugJack tipWireblack
19Volume first lugTone outer lugWireblack
20Tone middle lug.047 capWireblack

What each position does

SettingThe sourceEngine result
Position 1: BridgeNo legend printed; follows the labelled leads on the blade's standard contacts.Bridge single coil sized humbucker (both coils).
Position 2: Bridge + middleNo legend printed; follows the labelled leads on the blade's standard contacts.Middle Strat Stack Plus (both coils) and Bridge single coil sized humbucker (both coils) in parallel.
Position 3: MiddleNo legend printed; follows the labelled leads on the blade's standard contacts.Middle Strat Stack Plus (both coils).
Position 4: Middle + neckNo legend printed; follows the labelled leads on the blade's standard contacts.Neck Strat Stack Plus (both coils) and Middle Strat Stack Plus (both coils) in parallel.
Position 5: NeckNo legend printed; follows the labelled leads on the blade's standard contacts.Neck Strat Stack Plus (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The on-board component drawn across the bottom-coil pads of each Strat Stack Plus (no value printed) is not modelled.
  • The single-coil-sized humbucker is drawn as the Little '59 SL59-1 (Strat-size); hum cancelling and phase follow its lead colours and coil polarity as Seymour Duncan publishes them.
  • The sheet prints no position legend; the expected states follow the blade's standard contacts and the drawn lead labels.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • In each blade position the meter across the jack reads the pickup or pickup pair selected.
  • Each taped red & white joint and each taped Strat Stack Plus red reads about one coil's resistance to ground and to the hot lead, roughly half the pickup's total: not open, and not zero.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.