Skip to content
Tinkercaster

Seymour Duncan wiring

Two stacks and SCH, five-way, volume and two tones

2 stacks · SCH · 5-way · 1V · 2T

Transcribed from the manufacturer wiring sheet.

Viewed from the back of the controls, as you solder them.

Two stacks and SCH, five-way, volume and two tonesTwo stacks and SCH, five-way, volume and two tones: 2 stacks · SCH · 5-way · 1V · 2T. Original Tinkercaster drawing with labelled terminals.Neck stackMiddle Strat stackBridge stack250k250k250k22nFwhiteredblackbarewhiteredblackbareblackgreenwhiteredbareT1T2T3T4T5T6T7T8lug1lug2lug3lug1lug2lug3lug1lug2lug3abtipsleevegroundNeck stackMiddle Strat stackBridge stack5-Way Blade SwitchVolume 250kTone 1 (neck) · 250kTone 2 (middle) · 250k.022 cap · 22nFOutput jackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck stack—Strat Stack PlusAs specified
Middle Strat stack—Strat Stack PlusAs specified
Bridge stack—Little '59 SL59-1 Bridge (Strat-size)Example partSame wiring for JB Jr. SJBJ-1 Bridge (Strat-size), Hot Rails SHR-1 Bridge (Strat-size)
5-Way Blade Switch—Oak Grigsby 5-WayExample part
Volume 250k250kCTS 250k Audio PotExample part
Tone 1 (neck)250kCTS 250k Audio PotExample part
Tone 2 (middle)250kCTS 250k Audio PotExample part
.022 cap22nFOrange Drop .022µFExample part
Output jack—Switchcraft #11Example part
Bridge ground—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck stack gndVolume 250k casingWiregreen
2Neck stack bareVolume 250k casingWirebare
3Middle Strat Stack Plus gndVolume 250k casingWiregreen
4Middle Strat Stack Plus bareVolume 250k casingWirebare
5Bridge stack gndVolume 250k casingWiregreen
6Bridge stack bareVolume 250k casingWirebare
7Volume 250k lug1Volume 250k casingWireground
8Volume 250k casingOutput jack sleeveWireblack
9Bridge ground groundVolume 250k casingWireblack
10.022 cap bTone 1 (neck) casingWireblack
11Tone 1 (neck) casingVolume 250k casingWireblack
12Tone 2 (middle) casingTone 1 (neck) casingWireblack
13Bridge stack hot5-Way Blade Switch T3Wireblack
14Middle Strat Stack Plus hot5-Way Blade Switch T1Wireblack
15Neck stack hot5-Way Blade Switch T2Wireblack
165-Way Blade Switch T45-Way Blade Switch T8Wireblack
175-Way Blade Switch T8Volume 250k lug3Wireblack
185-Way Blade Switch T6Tone 1 (neck) lug1Wireblack
195-Way Blade Switch T5Tone 2 (middle) lug1Wireblack
20Bridge stack whiteBridge stack redWirered
21Volume 250k lug2Output jack tipWireblack
22Tone 1 (neck) lug2.022 cap aWireblack
23Tone 2 (middle) lug2Tone 1 (neck) lug2Wireblack
24Neck stack blackNeck stack whiteWirered
25Middle Strat Stack Plus blackMiddle Strat Stack Plus whiteWirered

What each position does

SettingThe sourceEngine result
BridgeEngine reading of the transcribed board.Bridge stack (both coils).
Bridge + middleEngine reading of the transcribed board.Middle Strat stack (both coils) and Bridge stack (both coils) in parallel.
MiddleEngine reading of the transcribed board.Middle Strat stack (both coils).
Middle + neckEngine reading of the transcribed board.Neck stack (both coils) and Middle Strat stack (both coils) in parallel.
NeckEngine reading of the transcribed board.Neck stack (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Shared-cap two-tone Strat wiring; toneReachesSignal may fail.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.