Parts and values
| In the drawing | Value | Part |
|---|---|---|
| Sixties P Neck | — | Sixties P™ Plug-In |
| Sixties J Bridge | — | Sixties J™ Bridge |
| Neck Volume 500K custom taper | 500k | CTS 500k Audio Pot |
| Bridge Volume 500K custom taper | 500k | CTS 500k Audio Pot |
| Master Tone 250K custom taper | 250k | CTS 250k Audio Pot |
| .033µF | 33nF | Orange Drop .033µF |
| Output jack | — | Switchcraft #11 |
| Bridge ground | — | Bridge ground wire |
Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.
Connections
In soldering order: grounds first, then the switch, the pickups and the signal path.
| # | From | To | How |
|---|---|---|---|
| 1 | Neck ground | Neck volume casing | To a pot casing |
| 2 | Neck volume ground lug | Neck volume casing | To a pot casing |
| 3 | Bridge ground | Bridge volume casing | To a pot casing |
| 4 | Bridge volume ground lug | Bridge volume casing | To a pot casing |
| 5 | .033µF capacitor | Tone casing | To a pot casing |
| 6 | Neck volume casing | Bridge volume casing | To a pot casing |
| 7 | Bridge volume casing | Tone casing | To a pot casing |
| 8 | Tone casing | Jack sleeve | Wire |
| 9 | TO BRIDGE GROUND | Jack sleeve | Shield or ground |
| 10 | Sixties P Neck bare shield | Neck volume casing | Shield or ground |
| 11 | Sixties P Neck second bare shield | Neck volume casing | Shield or ground |
| 12 | Sixties J Bridge bare shield | Bridge volume casing | Shield or ground |
| 13 | Sixties P Neck white | Neck Volume 500K custom taper lug2 | Wire |
| 14 | Sixties J Bridge red | Bridge Volume 500K custom taper lug2 | Wire |
| 15 | Sixties J Bridge white | Sixties J Bridge black | Joined and insulated |
| 16 | Pickup black (first half) | Pickup black (second half) | Joined and insulated |
| 17 | Neck Volume 500K custom taper lug3 | Bridge Volume 500K custom taper lug3 | Wire |
| 18 | Bridge Volume 500K custom taper lug3 | Master tone middle lug | Wire |
| 19 | Master tone middle lug | Jack tip | Wire |
| 20 | Master tone bottom lug | .033µF capacitor | Wire |
What it does
Engine result: Sixties P Neck (both coils) and Sixties J Bridge (both coils) in parallel.
Checked with the Tinkercaster wiring engine against the switching the source describes.
- The Sixties P and Sixties J pickups are drawn as their catalog parts; split-coil and hum-cancelling construction is not modelled.
- The source's custom-taper pots are not reproduced: pots are simulated with a linear track, so settings between the knob ends are approximate.
- Tone capacitor value matches the printed .033µF.
- Pickup resistance is not specified, so no numeric meter readings are given.
Before you solder
Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .
Check before plugging in
- With both volumes and the tone up, both pickups should read across the jack in parallel.
- Rolling either volume to zero should silence that pickup.
- The jack sleeve should read continuity to all three pot casings and the bridge ground wire.
Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.