Skip to content
Tinkercaster

DiMarzio wiring

Model P and Model J with two volumes and one tone

P-Bass · Jazz Bass bridge · No switch · Two volumes · One master tone

DiMarzio Model P (DP122BK) and Model J Bridge (DP123LBK) through independent 500K custom-taper volumes, a 250K custom-taper master tone and a .033 µF capacitor, to a Switchcraft two-conductor jack.

Viewed from the back of the controls, as you solder them.

Model P and Model J with two volumes and one toneModel P and Model J with two volumes and one tone: P-Bass · Jazz Bass bridge · No switch · Two volumes · One master tone. Original Tinkercaster drawing with labelled terminals.Model PModel J Bridge500k500k250k33nFredgreenblackwhiteredgreenblackwhitelug1lug2lug3lug1lug2lug3lug1lug2lug3abtipsleevegroundModel PModel J BridgeNeck Volume 500K custom taperBridge Volume 500K custom taperMaster Tone 250K custom taper.033µFOutput jackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Model PSource: Model P DP122BK (RED, GREEN, WHITE, BLACK)—DiMarzio Model P DP122Example part
Model J BridgeSource: Model J Bridge DP123LBK (RED, GREEN, WHITE, BLACK)—DiMarzio Model J DP123Example part
Neck Volume 500K custom taperSource: Neck Volume 500K custom taper pot (EP1201)500kCTS 500k Audio PotExample part
Bridge Volume 500K custom taperSource: Bridge Volume 500K custom taper pot (EP1201)500kCTS 500k Audio PotExample part
Master Tone 250K custom taperSource: Master Tone 250K custom taper pot (EP1200)250kCTS 250k Audio PotExample part
.033µFSource: .033µF capacitor (EP1033)33nFOrange Drop .033µFExample part
Output jackSource: Switchcraft output jack, 2-conductor (EP1301)—Switchcraft #11Example part
Bridge groundSource: TO BRIDGE GROUND—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck groundNeck volume casingTo a pot casinggreen
2Neck volume ground lugNeck volume casingTo a pot casing
3Bridge groundBridge volume casingTo a pot casinggreen
4Bridge volume ground lugBridge volume casingTo a pot casing
5.033µF capacitorTone casingTo a pot casing
6Neck volume casingBridge volume casingTo a pot casing
7Bridge volume casingTone casingTo a pot casing
8Tone casingJack sleeveWire
9TO BRIDGE GROUNDJack sleeveShield or ground
10Model P hotNeck Volume 500K custom taper lug2Wirered
11Model J Bridge hotBridge Volume 500K custom taper lug2Wirered
12Model P blackModel P whiteSeries link: soldered together and taped off, as the maker's sheet shows.Joined and insulatedblack
13Model J Bridge blackModel J Bridge whiteSeries link: soldered together and taped off, as the maker's sheet shows.Joined and insulatedblack
14Neck Volume 500K custom taper lug3Bridge Volume 500K custom taper lug3Wiresignal
15Bridge Volume 500K custom taper lug3Master tone middle lugWiresignal
16Master tone middle lugJack tipWire
17Master tone bottom lug.033µF capacitorWire

What it does

Engine result: Model P (both coils) and Model J Bridge (both coils) in parallel.

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The Model P and Model J pickups are drawn as their catalog parts; split-coil and hum-cancelling construction is not modelled.
  • The source's custom-taper pots are not reproduced: pots are simulated with a linear track, so settings between the knob ends are approximate.
  • Tone capacitor value matches the printed .033µF.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • With both volumes and the tone up, both pickups should read across the jack in parallel.
  • Rolling either volume to zero should silence that pickup.
  • The jack sleeve should read continuity to all three pot casings and the bridge ground wire.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.