Skip to content
Tinkercaster

Tonerider wiring

Tele with a neck Rebel 90 and a Tele bridge pickup

One P-90 style single coil · One single coil · Three-way blade · One volume · One tone

Tonerider's Rebel 90 + Tele Bridge harness: a neck Rebel 90 on a shielded lead and a Tele bridge single coil on a three-way blade, one 250k volume and one 250k tone with a .022 µF capacitor. The middle position runs both pickups in parallel.

Viewed from the back of the controls, as you solder them.

Tele with a neck Rebel 90 and a Tele bridge pickupTele with a neck Rebel 90 and a Tele bridge pickup: One P-90 style single coil · One single coil · Three-way blade · One volume · One tone. Original Tinkercaster drawing with labelled terminals.Neck Rebel 90Bridge pickup250k250k22nFwhiteblackbarewhiteblackT1T2T3T4T5T6T7T8lug1lug2lug3lug1lug2lug3abtipsleevegroundNeck Rebel 90Bridge pickup3-Way SwitchVolume 250kTone 250k.022 cap · 22nFOutput JackFrom Bridge Ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck Rebel 90Source: Neck Pickup (Rebel 90, shielded lead)—Tonerider Rebel 90As specified
Bridge pickupSource: Bridge Pickup (Tele bridge, white and black leads)—Tonerider Vintage Plus BridgeExample part
3-Way SwitchSource: 3-way blade (offset lugs)—CRL 3-Way BladeExample part
Volume 250k250kCTS 250k Audio PotExample part
Tone 250k250kCTS 250k Audio PotExample part
.022 capSource: .022µf cap (drawn orange)22nFOrange Drop .022µFExample part
Output JackSource: Output jack—Switchcraft #11Example part
From Bridge Ground—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck pickup shieldVolume casingDrawn to a ground symbol; the volume casing is a routing choice.Shield or groundbraided
2Bridge blackVolume casingTo a pot casingblack
3From Bridge GroundVolume casingShield or groundblack
4Volume right lugVolume casingLug bent onto the casing.To a pot casing
5.022µf capTone casingTo a pot casing
6Tone casingJack sleeveWireblack
7Volume casingTone casingRuns from the volume's bent-over lug down the right side.To a pot casingblack
8Neck Rebel 90 bare shieldVolume casingShield or groundbare
9Neck pickup inner leadSwitch top-right lug (common)Wireblack
10Bridge whiteSwitch bottom-left lug (common)Wirewhite
11Switch top-left lugSwitch second left lugJumperblack
12Switch second left lugSwitch third right lugJumperblack
13Switch third right lugSwitch bottom-right lugJumperblack
14Switch bottom-right lugVolume left lug (input)Wireblack
15Volume middle lugJack tipWirewhite
16Volume left lugTone left lugWireblack
17Tone middle lug.022µf capWire

What each position does

SettingThe sourceEngine result
Neck—Neck Rebel 90.
Neck + bridge—Neck Rebel 90 and Bridge pickup in parallel.
Bridge—Bridge pickup.

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Pickup resistance and magnet polarity are not specified, so no numeric meter readings or hum-cancelling claims are given.
  • The Rebel 90 is drawn from its catalog leads; its own construction is not modelled.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • In each blade position, the meter across the jack should read the selected pickup, or both in parallel in the middle.
  • With the volume at zero, tip and sleeve should read as a short.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.