Skip to content
Tinkercaster

DiMarzio wiring

Telecaster with a stacked-style bridge and a humbucker neck

Humbucker neck, stacked-style Tele bridge · Three-way Tele switch · One volume · One tone

DiMarzio's Telecaster harness with a four-conductor humbucker in the neck and an Area T stacked-style four-conductor bridge pickup, on a three-way Tele switch. On both pickups the black and white leads are joined and taped. On the Area T, the red and bare leads go to the volume casing and the green lead goes to the switch. It uses a 500K custom-taper volume, a 250K custom-taper tone, a .022 µF capacitor and a Switchcraft two-conductor jack.

Viewed from the back of the controls, as you solder them.

Telecaster with a stacked-style bridge and a humbucker neckTelecaster with a stacked-style bridge and a humbucker neck: Humbucker neck, stacked-style Tele bridge · Three-way Tele switch · One volume · One tone. Original Tinkercaster drawing with labelled terminals.Neck pickupArea T bridge500k250k22nFredgreenblackwhitebaregreenredblackwhitebareT1T2T3T4T5T6T7T8lug1lug2lug3lug1lug2lug3abtipsleevegroundNeck pickupArea T bridgeThree-way switchVolume 500K custom taperTone 250K custom taper.022µFOutput jackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck pickupSource: Neck pickup (BARE, GREEN, RED, BLACK, WHITE)—PAF Pro DP151Example partSame wiring for PAF 36th Anniversary Neck DP103, DiMarzio Air Classic Neck DP190, The Humbucker From Hell DP156, Evolution Neck DP158, D Activator Neck DP219, PAF Master Neck (4-conductor)
Area T bridgeSource: Area T™ bridge DP418 (RED, WHITE, BLACK, GREEN, BARE)—DiMarzio Area T Bridge DP418As specified
Three-way switchSource: Three-way switch for Tele® (EP1105)—CRL 3-Way BladeExample part
Volume 500K custom taperSource: Volume 500K custom taper pot (EP1201)500kCTS 500k Audio PotExample part
Tone 250K custom taperSource: Tone 250K custom taper pot (EP1200)250kCTS 250k Audio PotExample part
.022µFSource: .022µF capacitor (EP1022)22nFOrange Drop .022µFExample part
Output jackSource: Switchcraft® output jack, 2-conductor (EP1301)—Switchcraft #11Example part
Bridge groundSource: TO BRIDGE GROUND—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

  • DiMarzio humbucker wire colors

    Red is hot, black and white join each other, green and bare go to ground. See why, and what changes when you reverse the phase.

All DiMarzio wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck greenVolume casingTo a pot casinggreen
2Neck bare shieldVolume casingDrawn thin grey beside the green.Shield or groundbare
3Area T bridge gndVolume 500K custom taper casingWirered
4Bridge bare shieldVolume casingDrawn thin grey beside the bridge red to the lower casing dots.Shield or groundbare
5Volume casingVolume top lugTo a pot casingblack
6Volume top lugTone casingTo a pot casingblack
7.022 µF capacitorTone casingTo a pot casing
8Tone casingJack sleeveWireblack
9Bridge ground wireJack sleeveLabelled TO BRIDGE GROUND.Wireblack
10Neck redSwitch top-row first lugWhere it crosses the bridge red and bare it is drawn broken (a hop).Wirered
11Area T bridge hotThree-way switch T4Wiregreen
12Switch bottom-row first lugSwitch bottom-row second lugJumpergrey
13Switch bottom-row second lugSwitch top-row third lugJumpergrey
14Switch top-row third lugSwitch top-row fourth lugJumpergrey
15Switch top-row fourth lugVolume bottom lug (input)Wirelight grey
16Neck blackNeck whiteJoined at one solder dot with nothing else on it.Joined and insulatedblack
17Bridge blackBridge whiteJoined at one solder dot with nothing else on it.Joined and insulatedblack
18Volume middle lugJack tipWiredark grey
19Volume bottom lugTone middle lugWirelavender
20Tone bottom lug.022 µF capacitorWire

What each position does

SettingThe sourceEngine result
Neck—Neck pickup (both coils).
Neck and bridge—Neck pickup (both coils) and Area T bridge (both coils) in parallel.
Bridge—Area T bridge (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The source's custom-taper pots are not reproduced: both pots are simulated with a linear track, so settings between the knob ends are approximate.
  • The Area T bridge is simulated from its catalog leads; hum cancelling and phase follow the pickups' lead colours and coil polarity as DiMarzio publishes them; nothing here is measured.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • Position 1: continuity from jack tip to sleeve through the neck humbucker only.
  • Position 3: continuity through the bridge pickup only.
  • The taped black–white joints on both pickups should read about one coil's resistance to ground, roughly half the pickup's total (a few kΩ): not open, and not zero.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.