Skip to content
Tinkercaster

DiMarzio · The wiring reference

DiMarzio humbucker wire colors

Red is hot, black and white join each other, green and bare go to ground. See why, and what changes when you reverse the phase.

Applies to

DiMarzio four-conductor pickups with side-by-side coils, wired the standard way (series humbucking). Other brands use the same four colors for different jobs.

Match each wire to its job

Every DiMarzio four-conductor pickup has a red, a black, a green and a white wire, plus a bare wire. The table shows what each one does in the standard wiring, where the two coils work one after the other (in series) and cancel hum.

Standard series wiring · DiMarzio four-conductor pickup
WireWhere it goes
RedHot output
BlackJoin to white; tape the joint
WhiteJoin to black; tape the joint
GreenGround
BareGround, always
The standard series connection

This is how most humbuckers are wired, and what a plain replacement needs. Black and white are the two inner ends of the coils: joining them puts the coils in series. Red carries the signal. Green and the bare wire go to ground, which usually means the back of a pot.

If you are replacing a pickup, DiMarzio's advice is to note where the old one was connected before you remove it. In most cases red goes to the same place as the hot (or centre) wire of the old pickup.

  1. Solder the black and white wires to each other.
  2. Cover that joint with tape so it cannot touch any other part of the circuit.
  3. Solder red to the hot connection: the place the old pickup's hot wire went.
  4. Solder green and the bare wire to ground, usually the back of a pot. Keep the bare wire clear of every other connection.
Thin and weak with another pickup? Swap red and green

If the new pickup sounds weak and thin only when it is on together with another pickup, the two are out of phase. DiMarzio's fix is to reverse red and green: solder green to hot and red to ground. The bare wire still goes to ground and black and white stay joined.

The sheet says this applies to all DiMarzio pickups with side-by-side coils or blades when they share a guitar with single-coil pickups like those in a Stratocaster.

The same colors do not mean the same thing on other brands

DiMarzio's sheet warns that other makers' pickups may have the same color wires with different connections. On a Seymour Duncan humbucker, for example, black is hot and red and white are the pair you join. When you mix brands, match the job of each wire (hot, series link, ground), never the color.

The same colors do not mean the same thing on other brands
Job in standard series wiringDiMarzioSeymour Duncan
Hot outputRedBlack
Join and insulate (series link)Black + whiteRed + white
Coil return to groundGreenGreen
Shield to groundBareBare
See it in a complete guitar

The drawing below is DiMarzio's own diagram for one humbucker with a volume and a tone, redrawn so you can follow each wire. Find the red wire first, then the black and white pair.

Viewed from the back of the controls, as you solder them.

One humbucker with one volume and one toneDiMarzio's single bridge humbucker with 500K custom-taper volume and tone pots, a .022 µF capacitor and a Switchcraft two-conductor output jack. The tone signal enters at the tone pot's wiper.Bridge pickup500k500k22nFredgreenblackwhitebarelug1lug2lug3lug1lug2lug3tipsleeveabgroundBridge pickupVolume 500K custom taperTone 500K custom taperOutput jack.022µFBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Open the full page for this diagram →

Source and interpretation

Original explanation by Tinkercaster, based on DiMarzio 4-Conductor Pickup Instructions and the DiMarzio Product FAQ. The guide describes the stated configuration; it does not establish compatibility with every pickup or switch.

Not affiliated with or endorsed by DiMarzio. Refer to your exact pickup's instructions when a detail differs.

See it in a complete diagram

Put it in a complete circuit

Use a complete wiring diagram to see how the pickup, controls and output connect. Our public diagrams are free to view and explore.

Browse DiMarzio diagrams →

Understand this wiring

All DiMarzio wiring guides →