Skip to content
Tinkercaster

DiMarzio wiring

HS rail neck, hum bridge, one volume and one push/pull tone

Rail-style neck · Bridge humbucker · Three-way toggle · One volume · One push/pull tone

Transcribed from the manufacturer wiring sheet and checked against the engine.

Viewed from the back of the controls, as you solder them.

HS rail neck, hum bridge, one volume and one push/pull toneHS rail neck, hum bridge, one volume and one push/pull tone: Rail-style neck · Bridge humbucker · Three-way toggle · One volume · One push/pull tone. Original Tinkercaster drawing with labelled terminals.Neck rail-style pickupBridge humbucker500k500k22nFredgreenblackwhitebareredgreenblackwhitebareT1T2T3T4lug1lug2lug3lug1lug2lug3sw1sw2sw3sw4sw5sw6tipsleeveabgroundNeck rail-style pickupBridge humbucker3-Way ToggleVolume 500K custom taperTone 500K push/pullOutput jack.022µFBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck rail-style pickupSource: Neck rail-style pickup (BARE, GREEN, RED, BLACK, WHITE)—DiMarzio Fast Track 1 DP181Example partSame wiring for DiMarzio Fast Track 2 DP182, DiMarzio The Cruiser Neck DP186, DiMarzio The Chopper DP184, DiMarzio Air Norton S DP180, DiMarzio BC-1 DP225
Bridge humbuckerSource: Bridge humbucker (BARE, GREEN, RED, BLACK, WHITE)—Super Distortion DP100Example partSame wiring for DiMarzio Dual Sound DP101, DiMarzio Super 2 DP104, DiMarzio DLX Plus Bridge DP154, DiMarzio Norton DP160, DiMarzio Steve's Special DP161, DiMarzio D Sonic DP207
3-Way ToggleSource: 3-Way Toggle (Switchcraft, EP1101/EP1102)—Switchcraft 3-Way ToggleExample part
Volume 500K custom taperSource: Volume 500K custom taper (EP1201)500kCTS 500k Audio PotExample part
Tone 500K push/pullSource: Tone 500K push/pull (printed EP1201)500k500k Push-Pull DPDTExample part
Output jackSource: Output jack (Switchcraft, EP1301)—Switchcraft #11Example part
.022µFSource: .022µF capacitor (EP1022)22nFOrange Drop .022µFExample part
Bridge groundSource: TO BRIDGE GROUND—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

  • DiMarzio humbucker wire colors

    Red is hot, black and white join each other, green and bare go to ground. See why, and what changes when you reverse the phase.

All DiMarzio wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck pickup greenVolume casingWiregreen
2Neck pickup bareVolume casingWirebare
3Bridge pickup greenVolume casingWiregreen
4Bridge pickup bareVolume casingWirebare
53-Way Toggle T4 (frame)Jack sleeveThe toggle's ground lug runs along the bottom of the sheet to the jack sleeve.Wireblack
6Volume lug 1Volume casingWireblack
7Tone casingJack sleeveWireblack
8TO BRIDGE GROUNDJack sleeveWireblack
9.022µF bTone casingWireblack
10Tone casingVolume casingWireblack
11Neck pickup red (hot)3-Way Toggle T1Wirered
12Bridge pickup red (hot)3-Way Toggle T2Wirered
133-Way Toggle T3 (common)Volume input lugWiresignal
14Neck pickup blackNeck pickup whiteJoined at one end dot on the sheet (series link).Wireblack
15Bridge pickup blackBridge pickup whiteJoined at one end dot on the sheet (series link).Wireblack
16Volume wiperOutput jack tipWiresignal
17Volume input lugTone middle lug (wiper)Wiresignal
18Tone 500K push/pull lug1.022µF aWireblack

What each position does

SettingThe sourceEngine result
NeckPosition 1 = neck. The tone's push/pull contacts are not wired, so both states read the same.Neck rail-style pickup (both coils).
NeckPosition 1 = neck. The tone's push/pull contacts are not wired, so both states read the same.Neck rail-style pickup (both coils).
Neck and bridgePosition 2 = neck and bridge. The tone's push/pull contacts are not wired, so both states read the same.Neck rail-style pickup (both coils) and Bridge humbucker (both coils) in parallel.
Neck and bridgePosition 2 = neck and bridge. The tone's push/pull contacts are not wired, so both states read the same.Neck rail-style pickup (both coils) and Bridge humbucker (both coils) in parallel.
BridgePosition 3 = bridge. The tone's push/pull contacts are not wired, so both states read the same.Bridge humbucker (both coils).
BridgePosition 3 = bridge. The tone's push/pull contacts are not wired, so both states read the same.Bridge humbucker (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The source's 500K custom taper is not reproduced: the pots are simulated with the stand-in's audio taper.
  • The tone's push/pull contacts are not wired, so both push/pull states read the same.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • In each switch position, the meter across the jack should read the selected pickup, or both in parallel in the middle.
  • Each joined black–white pair should read about one coil's resistance to ground, roughly half the pickup's total (a few kΩ): not open, and not zero.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.