Skip to content
Tinkercaster

Seymour Duncan wiring

Tele with a bridge humbucker, neck single coil and push/pull volume coil split

One single coil · One humbucker · Three-way blade · One push/pull volume (coil split) · One tone

A Tele harness with a neck single coil and a bridge Seymour Duncan humbucker on a three-way blade, one 250k push/pull volume and one 250k tone with a .047 µF capacitor. Pulling the volume grounds the humbucker series link to split the bridge pickup.

Viewed from the back of the controls, as you solder them.

Tele with a bridge humbucker, neck single coil and push/pull volume coil splitTele with a bridge humbucker, neck single coil and push/pull volume coil split: One single coil · One humbucker · Three-way blade · One push/pull volume (coil split) · One tone. Original Tinkercaster drawing with labelled terminals.Neck single coilBridge humbucker250k250k47nFwhiteblackblackgreenwhiteredbareT1T2T3T4T5T6T7T8lug1lug2lug3sw1sw2sw3sw4sw5sw6lug1lug2lug3abtipsleevegroundNeck single coilBridge humbucker3-Way SwitchVolume 250k push/pullTone 250k.047 cap · 47nFOutput JackBridge ground wire

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck single coilSource: Seymour Duncan neck single coil—Vintage Tele Rhythm STR-1Example partSame wiring for Vintage '54 Tele Lead STL-1, Vintage Staggered Strat SSL-1, Vintage Flat Strat SSL-2, Quarter-Pound Flat Strat SSL-4, Custom SSL-5
Bridge humbuckerSource: Seymour Duncan Bridge Pickup (humbucker)—JB Model SH-4Example partSame wiring for Duncan Distortion SH-6 Bridge, Invader SH-8 Bridge, Duncan Custom SH-5, Seymour Duncan SH-3 Stag Mag, Seymour Duncan SH-11 Custom Custom, Seymour Duncan SH-2 Jazz Bridge
3-Way Switch—CRL 3-Way BladeExample part
Volume 250k push/pull250k250k Push-Pull DPDTExample part
Tone 250k250kCTS 250k Audio PotExample part
.047 cap47nFOrange Drop .047µFExample part
Output Jack—Switchcraft #11Example part
Bridge ground wireSource: bridge ground wire—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck single coil blackVolume 250k push/pull casingTo a pot casingblack
2Bridge humbucker greenVolume 250k push/pull casingTo a pot casinggreen
3Bridge ground wireVolume 250k push/pull casingTo a pot casingblack
4Volume 250k push/pull lug1Volume 250k push/pull casingTo a pot casing
5.047 cap bTone 250k casingTo a pot casingblack
6Tone 250k casingOutput Jack sleeveTo a pot casingblack
7Volume 250k push/pull casingTone 250k casingTo a pot casingblack
8Bridge humbucker bareVolume 250k push/pull casingTo a pot casingbare
9Volume 250k push/pull sw1Volume 250k push/pull casingTo a pot casingblack
10Neck single coil white3-Way Switch T8Wirewhite
11Bridge humbucker black3-Way Switch T4Wireblack
123-Way Switch T33-Way Switch T2Jumperblack
133-Way Switch T23-Way Switch T6Jumperblack
143-Way Switch T63-Way Switch T5Jumperblack
153-Way Switch T5Volume 250k push/pull lug3Wireblack
16Bridge humbucker whiteVolume 250k push/pull sw2Wirewhite
17Bridge humbucker redVolume 250k push/pull sw2Wirered
18Volume 250k push/pull lug2Output Jack tipWireblack
19Volume 250k push/pull lug3Tone 250k lug1Wireblack
20Tone 250k lug2.047 cap aWireblack

What each position does

SettingThe sourceEngine result
Neck, knob down—Neck single coil.
Neck + bridge, knob down—Neck single coil and Bridge humbucker (both coils) in parallel.
Bridge, knob down—Bridge humbucker (both coils).
Neck, knob pulled—Neck single coil.
Neck + bridge, knob pulled—Neck single coil and Bridge humbucker (split to one coil) in parallel.
Bridge, knob pulled—Bridge humbucker (split to one coil).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Hum cancelling and phase follow the pickups' lead colours and coil polarity as Seymour Duncan publishes them; nothing here is measured.
  • The source does not say which knob position splits; this follows the usual push/pull behaviour (pulled joins the middle lugs to the lugs nearest the pot).

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • Knob down: each blade position reads the selected full pickup(s).
  • Knob up: the humbucker(s) on the push/pull drop to roughly one coil.
  • With the volume at zero, tip and sleeve should read as a short in every position.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.