Skip to content
Tinkercaster

Seymour Duncan wiring

Tele neck humbucker bridge single, two volumes, neck volume push-pull split

Transcribed from the manufacturer wiring sheet and checked against the engine.

Viewed from the back of the controls, as you solder them.

Tele neck humbucker bridge single, two volumes, neck volume push-pull splitTele neck humbucker bridge single, two volumes, neck volume push-pull split: Tele neck humbucker bridge single, two volumes, neck volume push-pull split. Original Tinkercaster drawing with labelled terminals.Neck pickupBridge pickup250k250kblackgreenwhiteredbarewhiteblackT1T2T3T4T5T6T7T8lug1lug2lug3sw1sw2sw3sw4sw5sw6lug1lug2lug3tipsleevegroundNeck pickupBridge pickup3-Way SwitchNeck Volume 250k push/pullBridge Volume 250kOutput JackBridge Ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck pickup—Jazz Model SH-2 NeckExample partSame wiring for '59 Model SH-1 Neck, Seymour Duncan Antiquity Neck, Pearly Gates SH-PG1 Neck, Invader SH-8 Neck, Duncan Distortion SH-6 Neck, Alnico II Pro APH-1 Neck
Bridge pickup—Vintage '54 Tele Lead STL-1Example partSame wiring for Vintage Tele Rhythm STR-1, Vintage Staggered Strat SSL-1, Vintage Flat Strat SSL-2, Quarter-Pound Flat Strat SSL-4, Custom SSL-5
3-Way Switch—CRL 3-Way BladeExample part
Neck Volume 250k push/pull250k250k Push-Pull DPDTExample part
Bridge Volume 250k250kCTS 250k Audio PotExample part
Output Jack—Switchcraft #11Example part
Bridge Ground—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck pickup gndNeck Volume 250k push/pull casingWiregreen
2Bridge pickup gndBridge Volume 250k casingWireblack
3Neck Volume 250k push/pull lug1Neck Volume 250k push/pull casingWireground
4Bridge Volume 250k lug1Bridge Volume 250k casingWireground
5Neck Volume 250k push/pull casingBridge Volume 250k casingWireblack
6Bridge Volume 250k casingOutput Jack sleeveWireblack
7Bridge Ground groundNeck Volume 250k push/pull casingWireblack
8Neck pickup bareNeck Volume 250k push/pull casingWirebare
9Neck Volume 250k push/pull sw1Neck Volume 250k push/pull casingWireblack
10Neck Volume 250k push/pull lug23-Way Switch T8Wireblack
11Bridge Volume 250k lug23-Way Switch T4Wireblack
123-Way Switch T33-Way Switch T2Wireblack
133-Way Switch T23-Way Switch T6Wireblack
143-Way Switch T63-Way Switch T5Wireblack
153-Way Switch T5Output Jack tipWireblack
16Neck pickup hotNeck Volume 250k push/pull lug3Wireblack
17Bridge pickup hotBridge Volume 250k lug3Wirewhite
18Neck pickup whiteNeck Volume 250k push/pull sw2Wirewhite
19Neck pickup redNeck Volume 250k push/pull sw2Wirered

What each position does

SettingThe sourceEngine result
Position 1; p4=downEngine reading of the transcribed board; matches the source legend.Neck pickup (both coils).
Position 1; p4=upEngine reading of the transcribed board; matches the source legend.Neck pickup (split to one coil).
Position 2; p4=downEngine reading of the transcribed board; matches the source legend.Neck pickup (both coils) and Bridge pickup in parallel.
Position 2; p4=upEngine reading of the transcribed board; matches the source legend.Neck pickup (split to one coil) and Bridge pickup in parallel.
Position 3; p4=downEngine reading of the transcribed board; matches the source legend.Bridge pickup.
Position 3; p4=upEngine reading of the transcribed board; matches the source legend.Bridge pickup.

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Custom-taper pots are treated as linear by the simulator.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.