Skip to content
Tinkercaster

DiMarzio wiring

HSH with rail middle, super switch, volume and tone

HSH · Rail single middle · EP1112 5-way master switch · Volume · Tone

DiMarzio humbucker / rail single / humbucker harness on a 4-pole 5-way master switch with a 500K custom-taper volume, a 500K custom-taper tone and a .022µF capacitor. The two in-between positions split both selected pickups; the other three use one pickup whole.

Viewed from the back of the controls, as you solder them.

HSH with rail middle, super switch, volume and toneHSH with rail middle, super switch, volume and tone: HSH · Rail single middle · EP1112 5-way master switch · Volume · Tone. Original Tinkercaster drawing with labelled terminals.Neck humbuckerMiddle rail hum-canceling singleBridge humbucker500k500k22nFredgreenblackwhitebareredgreenblackwhitebareredgreenblackwhitebareT1T2T3T4T5T6T7T8T9T10T11T12T13T14T15T16T17T18T19T20T21T22T23T24lug1lug2lug3lug1lug2lug3abtipsleevegroundNeck humbuckerMiddle rail hum-canceling singleBridge humbucker5-way Super Switch (EP1112)Volume 500K custom taperTone 500K custom taper.022µFOutput jackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck humbuckerSource: Neck pickup—PAF Pro DP151Example partSame wiring for PAF 36th Anniversary Neck DP103, DiMarzio Air Classic Neck DP190, The Humbucker From Hell DP156, Evolution Neck DP158, D Activator Neck DP219, PAF Master Neck (4-conductor)
Middle rail hum-canceling singleSource: Middle rail single pickup—Pro TrackExample partSame wiring for DiMarzio The Chopper DP184, DiMarzio BC-1 DP225, DiMarzio BC-2 DP226, DiMarzio The Tone Zone S DP189, DiMarzio Super Distortion S DP218, DiMarzio Air Norton S DP180
Bridge humbuckerSource: Bridge pickup—Super Distortion DP100As specifiedSame wiring for DiMarzio Dual Sound DP101, DiMarzio Super 2 DP104, DiMarzio DLX Plus Bridge DP154, DiMarzio Norton DP160, DiMarzio Steve's Special DP161, DiMarzio D Sonic DP207
5-way Super Switch (EP1112)Source: 5-way 'Master Switch' for Strat multipole EP1112—Oak Grigsby 4-Pole 5-Way Super SwitchExample part
Volume 500K custom taperSource: Volume 500K custom taper pot EP1201500kCTS 500k Audio PotExample part
Tone 500K custom taperSource: Tone 500K custom taper pot EP1201500kCTS 500k Audio PotExample part
.022µFSource: .022µF capacitor EP102222nFOrange Drop .022µFExample part
Output jackSource: Switchcraft output jack (2-conductor) EP1301—Switchcraft #11Example part
Bridge groundSource: To bridge ground—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All DiMarzio wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck blackVolume casing (top)Runs over the top of the sheet.To a pot casingblack
2Neck bareVolume casing (top)Outermost grey loop over the top of the sheet.Shield or groundbare
3Neck greenLower row, right group, 4th lugBeside the neck red; drawn broken at the same place.Wiregreen
4Middle greenUpper row, far-left lugWiregreen
5Middle blackVolume casing (left)To a pot casingblack
6Middle bareVolume casing (left)Shield or groundbare
7Bridge greenLower row, right group, 2nd lugLoops under the switch beside the bridge red.Wiregreen
8Bridge blackVolume casing (left)Drawn broken where it passes behind the middle pickup's leads.To a pot casingblack
9Bridge bareVolume casing (left)Drawn broken beside the bridge black.Shield or groundbare
10Upper row, left group, 2nd lugUpper row, left group, 4th lugGrey jumper under the lugs.Wire
11Upper row, left group, 4th lugVolume casing (left)Grey wire up from the switch.To a pot casing
12Volume top lugVolume casing (top)To a pot casingblack
13Volume top lugTone casing (top)To a pot casingblack
14.022µF capacitorTone casing (bottom)Capacitor lead.To a pot casing
15Tone casing (bottom right)Jack sleeveRuns down the right edge of the sheet to the sleeve.Wireblack
16To bridge groundJack sleeveWireblack
17Neck redLower row, right group, 4th lugDrawn broken where it passes behind the middle pickup's black and bare leads.Wirered
18Neck whiteLower row, right group, 5th lugDrawn broken at the same place as the neck red and green.Wirewhite
19Middle whiteUpper row, right group, 2nd lugWirewhite
20Upper row, right group, 2nd lugUpper row, right group, 3rd lugGrey jumper.Wire
21Upper row, right group, 3rd lugUpper row, right group, 4th lugGrey jumper.Wire
22Middle redUpper row, far-left lugWirered
23Bridge whiteLower row, right group, 1st lugWirewhite
24Bridge redLower row, right group, 2nd lugLoops under the switch.Wirered
25Upper row, far-right lugVolume bottom lugLight grey wire.Wire
26Upper row, far-right lugLower row, far-right lugLight grey jumper at the right end of the switch.Wire
27Volume middle lugJack tipGrey wire.Wire
28Volume bottom lugTone middle lugDrawn lilac.Wirewhite
29Tone bottom lug.022µF capacitorCapacitor lead.Wire

What each position does

SettingThe sourceEngine result
Bridge (sheet Position 5)Position 5 = Bridge.Bridge humbucker (both coils).
Bridge split north + middle split south (sheet Position 4)Position 4 = Bridge Split North & Middle Split South.Middle rail hum-canceling single (split to one coil) and Bridge humbucker (split to one coil) in parallel.
Middle (sheet Position 3)Position 3 = Middle.Middle rail hum-canceling single (both coils).
Middle split south + neck split north (sheet Position 2)Position 2 = Middle Split South & Neck Split North.Neck humbucker (split to one coil) and Middle rail hum-canceling single (split to one coil) in parallel.
Neck (sheet Position 1)Position 1 = Neck.Neck humbucker (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The rail single middle is drawn as the Pro Track DP188; the rail construction is not modelled.
  • The 500K custom-taper pots are modelled by the catalog 500k audio pot; the simulator treats the taper as linear.
  • Every pickup is wired with red and green joined as the link between its coils, white as the output end and black to ground, so the lead roles in the catalog part (green = ground, black/white = series link) do not describe this wiring. The editor checks recognise this reversed-lead wiring (hot and return leads joined as the link).

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • In each switch position, the meter across the jack should read the pickup or split pair the legend names.
  • The tone casing should read continuity to the jack sleeve.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.