Parts and values
| In the drawing | Value | Part |
|---|---|---|
| Neck pickup | — | PAF Pro DP151 |
| Middle pickup (reverse polarity) | — | DiMarzio SDS-1 DP111 |
| Bridge pickup | — | Super Distortion DP100 |
| Five-way switch | — | Oak Grigsby 5-Way |
| Volume 500K custom taper | 500k | CTS 500k Audio Pot |
| Tone 500K custom taper | 500k | CTS 500k Audio Pot |
| .022µF | 22nF | Orange Drop .022µF |
| Output jack | — | Switchcraft #11 |
| Bridge ground | — | Bridge ground wire |
Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.
Understand this wiring
- DiMarzio humbucker wire colors
Red is hot, black and white join each other, green and bare go to ground. See why, and what changes when you reverse the phase.
Connections
In soldering order: grounds first, then the switch, the pickups and the signal path.
| # | From | To | How |
|---|---|---|---|
| 1 | Neck pickup gnd | Volume 500K custom taper casing | Wire |
| 2 | Neck pickup bare | Volume 500K custom taper casing | Wire |
| 3 | Middle pickup (reverse polarity) gnd | Volume 500K custom taper casing | Wire |
| 4 | Bridge pickup gnd | Volume 500K custom taper casing | Wire |
| 5 | Bridge pickup bare | Volume 500K custom taper casing | Wire |
| 6 | Five-way switch T5 | Volume 500K custom taper casing | Wire |
| 7 | Volume 500K custom taper lug1 | Volume 500K custom taper casing | Wire |
| 8 | Volume 500K custom taper lug1 | Tone 500K custom taper casing | Wire |
| 9 | .022µF b | Tone 500K custom taper casing | Wire |
| 10 | Tone 500K custom taper casing | Output jack sleeve | Wire |
| 11 | Bridge ground ground | Output jack sleeve | Wire |
| 12 | Neck pickup hot | Five-way switch T2 | Wire |
| 13 | Neck pickup black | Five-way switch T6 | Wire |
| 14 | Neck pickup white | Five-way switch T6 | Wire |
| 15 | Middle pickup (reverse polarity) hot | Five-way switch T1 | Wire |
| 16 | Bridge pickup hot | Five-way switch T3 | Wire |
| 17 | Bridge pickup black | Five-way switch T7 | Wire |
| 18 | Bridge pickup white | Five-way switch T7 | Wire |
| 19 | Five-way switch T4 | Volume 500K custom taper lug3 | Wire |
| 20 | Volume 500K custom taper lug2 | Output jack tip | Wire |
| 21 | Volume 500K custom taper lug3 | Tone 500K custom taper lug2 | Wire |
| 22 | Tone 500K custom taper lug1 | .022µF a | Wire |
What each position does
| Setting | The source | Engine result |
|---|---|---|
| Bridge | Source Position 5 = Bridge. | Bridge pickup (both coils). |
| Bridge split and middle | Source Position 4 = Bridge & Middle Split. | Middle pickup (reverse polarity) and Bridge pickup (split to one coil) in parallel. |
| Middle | Source Position 3 = Middle. | Middle pickup (reverse polarity). |
| Neck split and middle | Source Position 2 = Middle & Neck Split. | Neck pickup (split to one coil) and Middle pickup (reverse polarity) in parallel. |
| Neck | Source Position 1 = Neck. | Neck pickup (both coils). |
Checked with the Tinkercaster wiring engine against the switching the source describes.
- Custom tapers are not reproduced; pots are simulated as linear.
- Pickup resistance is not specified, so no numeric meter readings are given.
Before you solder
Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .
Check before plugging in
Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.