Skip to content
Tinkercaster

DiMarzio wiring

Steve Vai PIA HSH autosplit volume push-pull high-pass

Transcribed from the manufacturer wiring sheet and checked against the engine.

Viewed from the back of the controls, as you solder them.

Steve Vai PIA HSH autosplit volume push-pull high-passSteve Vai PIA HSH autosplit volume push-pull high-pass: Steve Vai PIA HSH autosplit volume push-pull high-pass. Original Tinkercaster drawing with labelled terminals.Neck UtoPIA DP287FMiddle UtoPIA DP288FBridge UtoPIA DP289F500k500k22nF0.33nFredblackwhitegreenbareredgreyblackredblackwhitegreenbareT1T2T3T4T5T6T7T8lug1lug2lug3sw1sw2sw3sw4sw5sw6lug1lug2lug3abtipsleevegroundabNeck UtoPIA DP287FMiddle UtoPIA DP288FBridge UtoPIA DP289F5-way switch EP1104Volume 500K push/pull (high-pass)Tone 500K custom taper.022µFOutput jackBridge ground330pF

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck UtoPIA DP287F—UtoPIA™ NeckAs specified
Middle UtoPIA DP288F—UtoPIA™ MiddleAs specified
Bridge UtoPIA DP289F—UtoPIA™ BridgeAs specified
5-way switch EP1104—Oak Grigsby 5-WayExample part
Volume 500K push/pull (high-pass)500k500k Push-Pull DPDTExample part
Tone 500K custom taper500kCTS 500k Audio PotExample part
.022µF22nFOrange Drop .022µFExample part
Output jack—Switchcraft #11Example part
Bridge ground—Bridge ground wireGeneric
330pF0.33nF330 pF Ceramic CapacitorExample part

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

  • DiMarzio humbucker wire colors

    Red is hot, black and white join each other, green and bare go to ground. See why, and what changes when you reverse the phase.

All DiMarzio wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck UtoPIA DP287F gndVolume 500K push/pull (high-pass) casingWiregreen
2Neck UtoPIA DP287F bareVolume 500K push/pull (high-pass) casingWirebare
3Middle UtoPIA DP288F black5-way switch EP1104 T1Wireblack
4Middle UtoPIA DP288F redVolume 500K push/pull (high-pass) casingWirered
5Bridge UtoPIA DP289F gndVolume 500K push/pull (high-pass) casingWiregreen
6Bridge UtoPIA DP289F bareVolume 500K push/pull (high-pass) casingWirebare
75-way switch EP1104 T5Volume 500K push/pull (high-pass) casingWireblack
8Volume 500K push/pull (high-pass) lug1Volume 500K push/pull (high-pass) casingWireground
9Volume 500K push/pull (high-pass) casingOutput jack sleeveWireblack
10Bridge ground groundVolume 500K push/pull (high-pass) casingWireblack
11Tone 500K custom taper lug2.022µF aWirebare
12.022µF bTone 500K custom taper casingWirebare
13Tone 500K custom taper casingVolume 500K push/pull (high-pass) casingWireblack
14Middle UtoPIA DP288F grey shieldVolume 500K push/pull (high-pass) casingShield or groundgrey
15Neck UtoPIA DP287F black5-way switch EP1104 T6Wireblack
16Neck UtoPIA DP287F hot5-way switch EP1104 T2Wirered
17Bridge UtoPIA DP289F black5-way switch EP1104 T7Wireblack
18Bridge UtoPIA DP289F hot5-way switch EP1104 T3Wirered
195-way switch EP1104 T4Volume 500K push/pull (high-pass) lug3Wiresignal
20Neck UtoPIA DP287F blackNeck UtoPIA DP287F whiteWireblack
21Bridge UtoPIA DP289F blackBridge UtoPIA DP289F whiteWireblack
22Volume 500K push/pull (high-pass) lug2Output jack tipWireblack
23Volume 500K push/pull (high-pass) lug3Tone 500K custom taper lug1Wireblack
24Volume 500K push/pull (high-pass) lug3330pF aWireyellow
25330pF bVolume 500K push/pull (high-pass) sw2Wireyellow
26Volume 500K push/pull (high-pass) sw1Volume 500K push/pull (high-pass) lug2Wireblack

What each position does

SettingThe sourceEngine result
Position 1; p5=downEngine reading of the transcribed board; matches the source legend.Bridge UtoPIA DP289F (both coils).
Position 1; p5=upEngine reading of the transcribed board; matches the source legend.Bridge UtoPIA DP289F (both coils).
Position 2; p5=downEngine reading of the transcribed board; matches the source legend.Middle UtoPIA DP288F and Bridge UtoPIA DP289F (split to one coil) in parallel.
Position 2; p5=upEngine reading of the transcribed board; matches the source legend.Middle UtoPIA DP288F and Bridge UtoPIA DP289F (split to one coil) in parallel.
Position 3; p5=downEngine reading of the transcribed board; matches the source legend.Middle UtoPIA DP288F.
Position 3; p5=upEngine reading of the transcribed board; matches the source legend.Middle UtoPIA DP288F.
Position 4; p5=downEngine reading of the transcribed board; matches the source legend.Neck UtoPIA DP287F (split to one coil) and Middle UtoPIA DP288F in parallel.
Position 4; p5=upEngine reading of the transcribed board; matches the source legend.Neck UtoPIA DP287F (split to one coil) and Middle UtoPIA DP288F in parallel.
Position 5; p5=downEngine reading of the transcribed board; matches the source legend.Neck UtoPIA DP287F (both coils).
Position 5; p5=upEngine reading of the transcribed board; matches the source legend.Neck UtoPIA DP287F (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Custom-taper pots are treated as linear by the simulator.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.