Parts and values
| In the drawing | Value | Part |
|---|---|---|
| Neck pickup | — | Little '59 SL59-1 Neck (Strat-size) |
| Middle single coil | — | Vintage Staggered Strat SSL-1 |
| Bridge pickup | — | Little '59 SL59-1 Bridge (Strat-size) |
| 5-Way Switch | — | Oak Grigsby 5-Way |
| Volume 250k push/pull | 250k | 250k Push-Pull DPDT |
| Output Jack | — | Switchcraft #11 |
| Ground wire to bridge | — | Bridge ground wire |
Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.
Understand this wiring
- Seymour Duncan humbucker wire colors
See the pickup, recognise its two halves, and learn where each coloured wire goes.
- Seymour Duncan coil splitting explained
A humbucker has two coils. See how a switch lets you use just one of them.
- Reading Seymour Duncan push/pull switch diagrams
Turning the knob and pulling it do different jobs. See the actual part, then try its switch connections.
Connections
In soldering order: grounds first, then the switch, the pickups and the signal path.
| # | From | To | How |
|---|---|---|---|
| 1 | Neck pickup gnd | Volume 250k push/pull casing | Wire |
| 2 | Neck pickup bare | Volume 250k push/pull casing | Wire |
| 3 | Middle single coil gnd | Volume 250k push/pull casing | Wire |
| 4 | Bridge pickup gnd | Volume 250k push/pull casing | Wire |
| 5 | Bridge pickup bare | Volume 250k push/pull casing | Wire |
| 6 | Ground wire to bridge ground | Volume 250k push/pull casing | Wire |
| 7 | Volume 250k push/pull lug1 | Volume 250k push/pull casing | Wire |
| 8 | Volume 250k push/pull lug nearest the pot, first row (sw1) | Volume 250k push/pull casing | To a pot casing |
| 9 | Volume 250k push/pull casing | Output Jack sleeve | Wire |
| 10 | Bridge pickup hot | 5-Way Switch T3 | Wire |
| 11 | Middle single coil hot | 5-Way Switch T1 | Wire |
| 12 | Neck pickup hot | 5-Way Switch T2 | Wire |
| 13 | 5-Way Switch T4 | 5-Way Switch T8 | Wire |
| 14 | 5-Way Switch T8 | Volume 250k push/pull lug3 | Wire |
| 15 | Neck pickup red | Volume 250k push/pull middle lug, first row (sw2) | Wire |
| 16 | Neck pickup white | Volume 250k push/pull middle lug, first row (sw2) | Wire |
| 17 | Bridge pickup red | Volume 250k push/pull middle lug, second row (sw5) | Wire |
| 18 | Bridge pickup white | Volume 250k push/pull middle lug, second row (sw5) | Wire |
| 19 | Volume 250k push/pull lug nearest the pot, first row (sw1) | Volume 250k push/pull lug nearest the pot, second row (sw4) | Wire |
| 20 | Volume 250k push/pull lug2 | Output Jack tip | Wire |
What each position does
| Setting | The source | Engine result |
|---|---|---|
| Position 1 · push | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. Pulled grounds the selected humbucker's red & white ('push/pull coil split'). | Bridge pickup (both coils). |
| Position 1 · pull | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. Pulled grounds the selected humbucker's red & white ('push/pull coil split'). | Bridge pickup (split to one coil). |
| Position 2 · push | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. Pulled grounds the selected humbucker's red & white ('push/pull coil split'). | Middle single coil and Bridge pickup (both coils) in parallel. |
| Position 2 · pull | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. Pulled grounds the selected humbucker's red & white ('push/pull coil split'). | Middle single coil and Bridge pickup (split to one coil) in parallel. |
| Position 3 · push | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. Pulled grounds the selected humbucker's red & white ('push/pull coil split'). | Middle single coil. |
| Position 3 · pull | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. Pulled grounds the selected humbucker's red & white ('push/pull coil split'). | Middle single coil. |
| Position 4 · push | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. Pulled grounds the selected humbucker's red & white ('push/pull coil split'). | Neck pickup (both coils) and Middle single coil in parallel. |
| Position 4 · pull | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. Pulled grounds the selected humbucker's red & white ('push/pull coil split'). | Neck pickup (split to one coil) and Middle single coil in parallel. |
| Position 5 · push | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. Pulled grounds the selected humbucker's red & white ('push/pull coil split'). | Neck pickup (both coils). |
| Position 5 · pull | The sheet prints no position legend; this is the standard 5-way contact table with the lugs mapped by function. Pulled grounds the selected humbucker's red & white ('push/pull coil split'). | Neck pickup (split to one coil). |
Checked with the Tinkercaster wiring engine against the switching the source describes.
- The single-coil-sized humbuckers are drawn as the Little '59 SL59-1 (Strat-size); hum cancelling and phase follow their lead colours and coil polarity as Seymour Duncan publishes them.
- The sheet does not say which knob position splits beyond 'push/pull coil split'; this follows the usual push/pull behaviour (pulled joins the middle lugs to the lugs nearest the pot).
- Pickup resistance is not specified, so no numeric meter readings are given.
Before you solder
Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .
Check before plugging in
- Knob pushed: positions 1, 2, 4 and 5 read the full humbucker they select.
- Knob pulled: the same positions read one humbucker coil; each humbucker's red & white read ground.
Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.