Skip to content
Tinkercaster

Seymour Duncan wiring

Two single-coil-sized humbuckers and a single coil, 5-way blade, push/pull split volume and tone

SCH · Single coil · SCH · 5-way blade · Push/pull volume (coil split) · One tone

Seymour Duncan sheet: single-coil-sized humbuckers in the neck and bridge and a single coil in the middle on a 5-way blade, with a push/pull volume that splits both humbuckers, one tone and a .047 cap. The sheet prints no pot values.

Viewed from the back of the controls, as you solder them.

Two single-coil-sized humbuckers and a single coil, 5-way blade, push/pull split volume and toneTwo single-coil-sized humbuckers and a single coil, 5-way blade, push/pull split volume and tone: SCH · Single coil · SCH · 5-way blade · Push/pull volume (coil split) · One tone. Original Tinkercaster drawing with labelled terminals.Neck single-coil-sized humbuckerMiddle single coilBridge single-coil-sized humbucker250k250k47nFblackgreenwhiteredbarewhiteblackblackgreenwhiteredbareT1T2T3T4T5T6T7T8lug1lug2lug3sw1sw2sw3sw4sw5sw6tipsleevegroundlug1lug2lug3abNeck single-coil-sized humbuckerMiddle single coilBridge single-coil-sized humbucker5-way bladeVolume (push/pull) · 250kOutput jackBridge groundTone · 250k.047 cap · 47nF

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck single-coil-sized humbuckerSource: Neck single coil sized humbucker—Little '59 SL59-1 Neck (Strat-size)Example partSame wiring for JB Jr. SJBJ-1 Bridge (Strat-size), Hot Rails SHR-1 Bridge (Strat-size)
Middle single coil—Vintage Staggered Strat SSL-1Example partSame wiring for Vintage Flat Strat SSL-2, Quarter-Pound Flat Strat SSL-4, Alnico II Pro Staggered Strat APS-1, Custom SSL-5
Bridge single-coil-sized humbuckerSource: Bridge single coil sized humbucker—Little '59 SL59-1 Bridge (Strat-size)Example partSame wiring for JB Jr. SJBJ-1 Bridge (Strat-size), Hot Rails SHR-1 Bridge (Strat-size)
5-way bladeSource: 5 way blade—Oak Grigsby 5-WayExample part
Volume (push/pull)Source: Volume push/pull coil split250kNot on the sheet; stand-in250k Push-Pull DPDTExample part
Output jackSource: Output Jack—Switchcraft #11Example part
Bridge groundSource: Bridge Ground—Bridge ground wireGeneric
Tone250kNot on the sheet; stand-inCTS 250k Audio PotExample part
.047 cap47nFOrange Drop .047µFExample part

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck greenVolume casing (Solder spot)Neck green to the Solder spot on the volume casing.To a pot casinggreen
2Neck bareVolume casing (Solder spot)Neck bare (drawn grey beside the green) to the Solder spot on the volume casing.Shield or groundbare
3Middle blackVolume casing (Solder spot)Middle black runs down beside the bridge pickup and back to the Solder spot on the volume casing.To a pot casingblack
4Bridge greenVolume casing (Solder spot)Bridge green to the Solder spot on the volume casing.To a pot casinggreen
5Bridge bareVolume casing (Solder spot)Bridge bare (drawn grey) to the Solder spot on the volume casing.Shield or groundbare
6Push/pull neck-pair column, lug nearest the potVolume casing (Solder spot)Short black from the push/pull lug nearest the pot to the upper Solder spot on the volume casing.To a pot casingblack
7Volume third lugVolume casing (Solder spot)Volume outer lug bent onto the casing under the Solder spot.To a pot casing
8Volume casing (Solder spot)Jack SleeveBlack from the volume Solder spot to the jack Sleeve (ground).To a pot casingblack
9Bridge Ground wireVolume casing (Solder spot)Bridge Ground wire to the volume Solder spot.To a pot casingblack
10.047 capTone casing (Solder spot)Other cap leg to the tone casing under its Solder spot.To a pot casing
11Tone casing (Solder spot)Volume casing (Solder spot)Black from the tone Solder spot to the volume Solder spot; it carries a hop over the white wire to the jack.To a pot casingblack
12Neck blackBlade wired row, second lugNeck black (from the neck cable) arcs over the top of the blade to the wired row, second lug from the common.Wireblack
13Middle whiteBlade wired row, third lugMiddle white loops over the blade to the wired row, third lug from the common.Wirewhite
14Bridge blackBlade wired row, top lugBridge black (from the bridge cable) to the wired row, lug furthest from the common.Wireblack
15Blade wired row, bottom lug (common)Blade opposite row, top lugWhite from the wired row common (bottom lug) runs along the blade to the opposite row's end lug (top).Wirewhite
16Blade opposite row, top lugVolume first lug (input)White from that opposite-row end lug down to the volume input lug.Wirewhite
17Neck redPush/pull neck-pair column, middle lugNeck red runs with its white from the neck cable over the top of the push/pull to the middle lug of one push/pull column.Wirered
18Neck whitePush/pull neck-pair column, middle lugNeck white with its red to the same push/pull middle lug.Wirewhite
19Bridge redPush/pull bridge-pair column, middle lugBridge red runs with its white from the bridge cable up to the middle lug of the other push/pull column.Wirered
20Bridge whitePush/pull bridge-pair column, middle lugBridge white with its red to the same push/pull middle lug.Wirewhite
21Push/pull neck-pair column, lug nearest the potPush/pull bridge-pair column, lug nearest the potShort black jumper between the two push/pull lugs nearest the pot.Wireblack
22Volume middle lugJack TipWhite from the volume middle lug to the jack Tip (hot output).Wirewhite
23Volume first lug (input)Tone outer lugWire from the volume input lug to the tone lug at the end nearest the volume.Wirewhite
24Tone middle lug.047 capTone middle lug to one leg of the .047 cap.Wireblack

What each position does

SettingThe sourceEngine result
Position 1 · push: bridgeKnob down: both red & white pairs float, so each humbucker is full.Bridge single-coil-sized humbucker (both coils).
Position 1 · pull: bridge splitKnob up: the push/pull grounds both red & white pairs, splitting whichever humbucker is selected.Bridge single-coil-sized humbucker (split to one coil).
Position 2 · push: bridge + middleKnob down: both red & white pairs float, so each humbucker is full.Middle single coil and Bridge single-coil-sized humbucker (both coils) in parallel.
Position 2 · pull: bridge split + middleKnob up: the push/pull grounds both red & white pairs, splitting whichever humbucker is selected.Middle single coil and Bridge single-coil-sized humbucker (split to one coil) in parallel.
Position 3 · push: middleKnob down: both red & white pairs float, so each humbucker is full.Middle single coil.
Position 3 · pull: middleKnob up: the push/pull grounds both red & white pairs, splitting whichever humbucker is selected.Middle single coil.
Position 4 · push: middle + neckKnob down: both red & white pairs float, so each humbucker is full.Neck single-coil-sized humbucker (both coils) and Middle single coil in parallel.
Position 4 · pull: middle + neck splitKnob up: the push/pull grounds both red & white pairs, splitting whichever humbucker is selected.Neck single-coil-sized humbucker (split to one coil) and Middle single coil in parallel.
Position 5 · push: neckKnob down: both red & white pairs float, so each humbucker is full.Neck single-coil-sized humbucker (both coils).
Position 5 · pull: neck splitKnob up: the push/pull grounds both red & white pairs, splitting whichever humbucker is selected.Neck single-coil-sized humbucker (split to one coil).

Not simulated: this circuit is drawn for reference only.

  • The sheet prints no pot values; 250k stand-ins are used.
  • Which shaft position grounds the red & white pairs follows the usual push/pull behaviour (pulled joins the middle lugs to the lugs nearest the pot); the sheet does not say which way splits.
  • The single-coil-sized humbuckers are drawn as the Little '59 SL59-1 (Strat-size); hum cancelling and phase follow its lead colours and coil polarity as Seymour Duncan publishes them.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • Knob down: in each blade position the meter across the jack reads the full pickup or pickup pair selected.
  • Knob up: both humbuckers' red & white read ground; positions 1 and 5 drop to one coil's reading.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.