Skip to content
Tinkercaster

Seymour Duncan wiring

HSH, 5-way blade, push/pull split volume and tone

Humbucker · Single coil · Humbucker · 5-way blade · Push/pull volume (coil split) · One tone

Seymour Duncan sheet: humbuckers in the neck and bridge and a single coil in the middle on a 5-way blade, with a 250k (or 500k) push/pull volume that splits both humbuckers, a 250k tone and a .047 cap. The neck humbucker's green and bare are not drawn on the current sheet and are added from Seymour Duncan's 2006 original of it.

Viewed from the back of the controls, as you solder them.

HSH, 5-way blade, push/pull split volume and toneHSH, 5-way blade, push/pull split volume and tone: Humbucker · Single coil · Humbucker · 5-way blade · Push/pull volume (coil split) · One tone. Original Tinkercaster drawing with labelled terminals.Neck humbuckerMiddle single coilBridge humbucker250k250k47nFblackgreenwhiteredbarewhiteblackblackgreenwhiteredbareT1T2T3T4T5T6T7T8lug1lug2lug3sw1sw2sw3sw4sw5sw6tipsleevegroundlug1lug2lug3abNeck humbuckerMiddle single coilBridge humbucker5-way bladeVolume 250k (push/pull)Output jackBridge groundTone 250k.047 cap · 47nF

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck humbucker—'59 Model SH-1 NeckExample partSame wiring for Jazz Model SH-2 Neck, Duncan Distortion SH-6 Neck, Invader SH-8 Neck, Pearly Gates SH-PG1 Neck, Alnico II Pro APH-1 Neck
Middle single coil—Vintage Staggered Strat SSL-1Example partSame wiring for Vintage Flat Strat SSL-2, Quarter-Pound Flat Strat SSL-4, Alnico II Pro Staggered Strat APS-1, Custom SSL-5
Bridge humbucker—JB Model SH-4Example partSame wiring for Duncan Custom SH-5, Duncan Distortion SH-6 Bridge, Invader SH-8 Bridge, Seymour Duncan SH-2 Jazz Bridge, Seymour Duncan SH-3 Stag Mag, Custom Five SH-14
5-way bladeSource: 5-way blade switch—Oak Grigsby 5-WayExample part
Volume 250k (push/pull)Source: Volume 250k (or 500k), push/pull coil split250k250k Push-Pull DPDTExample part
Output jackSource: Output Jack—Switchcraft #11Example part
Bridge ground—Bridge ground wireGeneric
Tone 250k250kCTS 250k Audio PotExample part
.047 cap47nFOrange Drop .047µFExample part

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck green (added, not drawn on this sheet)Volume Solder spotNeck green to the volume Solder spot. Not drawn on the current sheet. Added from Seymour Duncan's 2006 original of this sheet (hsh_1v_1t_5w_pushpull.pdf), which runs the neck green and bare to the volume Solder spot.To a pot casinggreen
2Neck bare (added, not drawn on this sheet)Volume Solder spotNeck bare to the volume Solder spot. Not drawn on the current sheet. Added from Seymour Duncan's 2006 original of this sheet (hsh_1v_1t_5w_pushpull.pdf), which runs the neck green and bare to the volume Solder spot.Shield or groundbare
3Middle blackVolume Solder spotMiddle black runs straight down past the bridge pickup and left to the volume Solder spot.To a pot casingblack
4Bridge greenVolume Solder spotBridge green to the volume Solder spot.To a pot casinggreen
5Bridge bareVolume Solder spotBridge bare (drawn grey beside the green) to the volume Solder spot.Shield or groundbare
6Push/pull neck-pair column, lug nearest the potVolume Solder spotBlack from the neck-pair column's lug nearest the pot, curving down across the casing to the volume Solder spot.To a pot casingblack
7Volume third lugVolume Solder spotThe volume's third lug is drawn bent onto the casing under the Solder spot.To a pot casing
8Volume Solder spotJack SleeveFrom the volume Solder spot down to the jack Sleeve (ground).To a pot casingblack
9Volume casingTone Solder spotFrom the bottom of the volume casing straight down and left to the tone Solder spot.To a pot casingblack
10.047 capTone Solder spotOther cap leg to the tone Solder spot.To a pot casing
11Bridge ground wireTone Solder spotWire from the tone Solder spot leaving the page, labelled 'Bridge ground'.Shield or groundblack
12Neck blackBlade wired row, second lug from the commonNeck black leaves the neck cable on the right, runs left under the middle pickup and arcs over the blade to the wired row, second lug from the common.Wireblack
13Middle whiteBlade wired row, third lug from the commonMiddle white (drawn as a white lead) loops over the blade to the wired row, third lug from the common.Wirewhite
14Bridge blackBlade wired row, lug furthest from the commonBridge black leaves the bridge cable, runs up and over to the wired row, lug furthest from the common.Wireblack
15Blade wired row, bottom lug (common)Volume first lug (input)From the wired row's bottom lug (common) down round the left of the blade to the volume's first lug.Wireblack
16Neck redPush/pull neck-pair column, middle lugNeck red runs with its white down the right side and back to the middle lug of one push/pull column.Wirered
17Neck whitePush/pull neck-pair column, middle lugNeck white with its red to the same push/pull middle lug.Wirewhite
18Bridge redPush/pull bridge-pair column, middle lugBridge red runs with its white from the bridge cable to the middle lug of the other push/pull column.Wirered
19Bridge whitePush/pull bridge-pair column, middle lugBridge white with its red to the same push/pull middle lug.Wirewhite
20Push/pull neck-pair column, lug nearest the potPush/pull bridge-pair column, lug nearest the potShort black jumper between the two push/pull lugs nearest the pot.Wireblack
21Volume middle lugJack TipFrom the volume's middle lug down and right to the jack Tip (hot output); it hops the ground wires it crosses.Wireblack
22Volume first lug (input)Tone outer lug nearest the volumeFrom the volume's first lug to the tone's outer lug nearest the volume (tone drawn lugs up).Wireblack
23Tone middle lug.047 capTone middle lug to one leg of the .047 cap.Wireblack

What each position does

SettingThe sourceEngine result
Position 1 · push: bridgeKnob down: both humbuckers' red & white pairs sit on the empty push/pull lugs, so each humbucker is full.Bridge humbucker (both coils).
Position 1 · pull: bridge splitKnob up: both red & white pairs join the jumpered, grounded push/pull lugs, splitting whichever humbucker is selected.Bridge humbucker (split to one coil).
Position 2 · push: bridge + middleKnob down: both humbuckers' red & white pairs sit on the empty push/pull lugs, so each humbucker is full.Middle single coil and Bridge humbucker (both coils) in parallel.
Position 2 · pull: bridge split + middleKnob up: both red & white pairs join the jumpered, grounded push/pull lugs, splitting whichever humbucker is selected.Middle single coil and Bridge humbucker (split to one coil) in parallel.
Position 3 · push: middleKnob down: both humbuckers' red & white pairs sit on the empty push/pull lugs, so each humbucker is full.Middle single coil.
Position 3 · pull: middleKnob up: both red & white pairs join the jumpered, grounded push/pull lugs, splitting whichever humbucker is selected.Middle single coil.
Position 4 · push: middle + neckKnob down: both humbuckers' red & white pairs sit on the empty push/pull lugs, so each humbucker is full.Neck humbucker (both coils) and Middle single coil in parallel.
Position 4 · pull: middle + neck splitKnob up: both red & white pairs join the jumpered, grounded push/pull lugs, splitting whichever humbucker is selected.Neck humbucker (split to one coil) and Middle single coil in parallel.
Position 5 · push: neckKnob down: both humbuckers' red & white pairs sit on the empty push/pull lugs, so each humbucker is full.Neck humbucker (both coils).
Position 5 · pull: neck splitKnob up: both red & white pairs join the jumpered, grounded push/pull lugs, splitting whichever humbucker is selected.Neck humbucker (split to one coil).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The neck humbucker's green and bare are not drawn on the current sheet; they are added from other Seymour Duncan sources (see notes).
  • Which shaft position grounds the red & white pairs follows the usual push/pull behaviour (pulled joins the middle lugs to the lugs nearest the pot); the sheet does not say which way splits.
  • The 250k value is used; the sheet also allows 500k.
  • Custom tapers are not reproduced; pots are simulated as linear.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • Knob down: in each blade position the meter across the jack reads the full pickup or pickup pair selected.
  • Knob up: both humbuckers' red & white read ground; positions 1 and 5 drop to one coil's reading.
  • Neck green and bare read ground at the volume casing (the added leads).

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.