Skip to content
Tinkercaster

DiMarzio wiring

HSH with stacked middle, super switch, volume and tone

HSH · Stacked single middle · EP1112 5-way master switch · Volume · Tone

DiMarzio humbucker / stacked single / humbucker harness on a 4-pole 5-way master switch with a 500K custom-taper volume, a 500K custom-taper tone and a .022µF capacitor. The two in-between positions split both selected pickups; the other three use one pickup whole.

Viewed from the back of the controls, as you solder them.

HSH with stacked middle, super switch, volume and toneHSH with stacked middle, super switch, volume and tone: HSH · Stacked single middle · EP1112 5-way master switch · Volume · Tone. Original Tinkercaster drawing with labelled terminals.Neck humbuckerMiddle stacked singleBridge humbucker500k500k22nFredgreenblackwhitebaregreenredblackwhitebareredgreenblackwhitebareT1T2T3T4T5T6T7T8T9T10T11T12T13T14T15T16T17T18T19T20T21T22T23T24lug1lug2lug3lug1lug2lug3abtipsleevegroundNeck humbuckerMiddle stacked singleBridge humbucker5-way Super Switch (EP1112)Volume 500K custom taperTone 500K custom taper.022µFOutput jackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck humbuckerSource: Neck pickup—PAF Pro DP151Example partSame wiring for PAF 36th Anniversary Neck DP103, DiMarzio Air Classic Neck DP190, The Humbucker From Hell DP156, Evolution Neck DP158, D Activator Neck DP219, PAF Master Neck (4-conductor)
Middle stacked singleSource: Middle stacked single pickup—Area 67 DP419Example partSame wiring for Area 58 DP415, Area 61 DP416, DiMarzio Virtual Solo DP420, DiMarzio Virtual Vintage Blues DP402, Virtual Vintage 54 Pro DP408, Injector Neck
Bridge humbuckerSource: Bridge pickup—Super Distortion DP100As specifiedSame wiring for DiMarzio Dual Sound DP101, DiMarzio Super 2 DP104, DiMarzio DLX Plus Bridge DP154, DiMarzio Norton DP160, DiMarzio Steve's Special DP161, DiMarzio D Sonic DP207
5-way Super Switch (EP1112)Source: 5-way 'Master Switch' for Strat multipole EP1112—Oak Grigsby 4-Pole 5-Way Super SwitchExample part
Volume 500K custom taperSource: Volume 500K custom taper pot EP1201500kCTS 500k Audio PotExample part
Tone 500K custom taperSource: Tone 500K custom taper pot EP1201500kCTS 500k Audio PotExample part
.022µFSource: .022µF capacitor EP102222nFOrange Drop .022µFExample part
Output jackSource: Switchcraft output jack (2-conductor) EP1301—Switchcraft #11Example part
Bridge groundSource: To bridge ground—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All DiMarzio wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck redVolume casing (top)Runs over the top of the sheet.To a pot casingred
2Neck bareVolume casing (top)Outermost grey loop over the top of the sheet.Shield or groundbare
3Neck greenLower row, right group, 5th lugDrawn broken at the same place as the neck black and white.Wiregreen
4Middle stacked single gnd5-way Super Switch (EP1112) T8Wirered
5Middle stacked single hotVolume 500K custom taper casingWiregreen
6Bridge greenLower row, right group, 1st lugWiregreen
7Bridge redVolume casing (left)Drawn broken where it passes behind the middle pickup's leads.To a pot casingred
8Bridge bareVolume casing (left)Drawn broken beside the bridge red.Shield or groundbare
9Upper row, left group, 2nd lugUpper row, left group, 4th lugGrey jumper under the lugs.Wire
10Upper row, left group, 4th lugVolume casing (left)Grey wire up from the switch.To a pot casing
11Volume top lugVolume casing (top)To a pot casingblack
12Volume top lugTone casing (top)To a pot casingblack
13.022µF capacitorTone casing (bottom)Capacitor lead.To a pot casing
14Tone casing (bottom right)Jack sleeveRuns down the right edge of the sheet to the sleeve.Wireblack
15To bridge groundJack sleeveWireblack
16Neck blackLower row, right group, 4th lugDrawn broken where it passes behind the middle pickup's leads.Wireblack
17Neck whiteLower row, right group, 4th lugBeside the neck black; drawn broken at the same place.Wirewhite
18Upper row, right group, 2nd lugUpper row, right group, 3rd lugRed jumper.Wirered
19Upper row, right group, 3rd lugUpper row, right group, 4th lugRed jumper.Wirered
20Middle whiteUpper row, far-left lugWirewhite
21Middle blackUpper row, far-left lugWireblack
22Bridge blackLower row, right group, 2nd lugLoops under the switch.Wireblack
23Bridge whiteLower row, right group, 2nd lugLoops under the switch beside the bridge black.Wirewhite
24Upper row, far-right lugVolume bottom lugLight grey wire.Wire
25Upper row, far-right lugLower row, far-right lugLight grey jumper at the right end of the switch.Wire
26Volume middle lugJack tipGrey wire.Wire
27Volume bottom lugTone middle lugDrawn lilac.Wirewhite
28Tone bottom lug.022µF capacitorCapacitor lead.Wire

What each position does

SettingThe sourceEngine result
Bridge (sheet Position 5)Position 5 = Bridge.Bridge humbucker (both coils).
Bridge split north + middle split top coil (sheet Position 4)Position 4 = Bridge Split North & Middle Split Top Coil (South).Middle stacked single (split to one coil) and Bridge humbucker (split to one coil) in parallel.
Middle (sheet Position 3)Position 3 = Middle.Middle stacked single (both coils).
Middle split top coil + neck split north (sheet Position 2)Position 2 = Middle Split Top Coil (South) & Neck Split North.Neck humbucker (split to one coil) and Middle stacked single (split to one coil) in parallel.
Neck (sheet Position 1)Position 1 = Neck.Neck humbucker (both coils).

Not simulated: this circuit is drawn for reference only.

  • The stacked single middle is drawn as the Area 67 DP419; the stacked construction is not modelled, and the catalog's coil names do not identify the sheet's 'top coil (south)'.
  • The 500K custom-taper pots are modelled by the catalog 500k audio pot; the simulator treats the taper as linear.
  • The neck and bridge humbuckers take green as the output end and red to ground, so the catalog lead roles (red = hot, green = ground) are reversed on this sheet; one editor check misjudges it (see rule exceptions).

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • In each switch position, the meter across the jack should read the pickup or split pair the legend names.
  • The tone casing should read continuity to the jack sleeve.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.