Skip to content
Tinkercaster

DiMarzio · The wiring reference

DiMarzio coil splitting explained

A switch sends the black and white pair to ground, which turns one coil off. See what to wire and what it does to the sound.

Applies to

DiMarzio four-conductor pickups. DiMarzio calls this single-coil switching, and also coil tapping or coil splitting. Stacked models (HS, Area, Virtual Vintage) behave differently, as noted below.

What changes when you split

Splitting turns one of the two coils off, so the pickup works as a single coil. DiMarzio describes the result as a brighter, cleaner sound.

With side-by-side humbuckers the split sound is quieter than the full humbucker. It also stops cancelling hum: the sheet is explicit that turning off a coil means the pickup is no longer humbucking.

Wire the switch

The pickup stays wired as normal: red to hot, green and bare to ground. The only change is the black and white pair. Instead of being taped off, the pair goes to a switch, and the switch connects it to ground when you want the single-coil sound.

Any switch that can join two points works. DiMarzio shows a double-pole, double-throw (DPDT) mini-switch and says a simpler single-pole, double-throw switch does the job too. A push-pull pot (DiMarzio EP1200PP at 250K, EP1201PP at 500K) has the same DPDT switch built in, so you do not have to drill a hole.

  1. Wire red to hot and green and bare to ground, as in the standard connection.
  2. Solder the joined black and white pair to the middle lug of one side of the switch.
  3. Run a wire from the neighbouring lug on that side to ground.
  4. Check both positions: one is the full humbucker, the other is the single coil.
Split two pickups with one switch

A DPDT switch has two independent sides and a split only uses one. DiMarzio's sheet uses the spare side for a second pickup: the first pickup's black and white pair goes to one side, the second pickup's pair to the other, and both sides go to ground. One pull then splits both pickups.

Stacked pickups: HS, Area and Virtual Vintage

These single-coil-size pickups have their coils one above the other. The sheet says that when they are split, the volume is slightly greater, as long as the coil closest to the strings stays on. That is the coil with the red and black wires.

DiMarzio also says phase switching should not be combined with a coil split on these models: in one position only the bottom coil is on, producing almost no signal.

See it in a complete guitar

This DiMarzio diagram splits both humbuckers of a Les Paul style guitar from a push-pull tone pot. Follow the black and white pairs to the switch under the pot.

Viewed from the back of the controls, as you solder them.

Les Paul coil split (master tone push/pull)DiMarzio's Les Paul coil split: two volumes, two tones, and a push/pull on the neck tone that splits both humbuckers at once, the bridge to its north coil and the neck to its south.Neck PickupBridge Pickup500k500k500k500k22nF22nFredgreenblackwhitebareredgreenblackwhitebareT1T2T3T4lug1lug2lug3lug1lug2lug3lug1lug2lug3sw1sw2sw3sw4sw5sw6lug1lug2lug3tipsleevegroundababNeck PickupBridge Pickup3-Way ToggleNeck Volume 500kABridge Volume 500kANeck tone 500K push/pull (master split)Bridge Tone 500kAOutput JackBridge ground.022µf (neck).022µf (bridge)

Open the interactive diagram to zoom, move components and try the switches.

Open the full page for this diagram →

Source and interpretation

Original explanation by Tinkercaster, based on DiMarzio 4-Conductor Pickup Instructions. The guide describes the stated configuration; it does not establish compatibility with every pickup or switch.

Not affiliated with or endorsed by DiMarzio. Refer to your exact pickup's instructions when a detail differs.

See it in a complete diagram

Put it in a complete circuit

Use a complete wiring diagram to see how the pickup, controls and output connect. Our public diagrams are free to view and explore.

Browse DiMarzio diagrams →

Understand this wiring

All DiMarzio wiring guides →