Skip to content
Tinkercaster

DiMarzio wiring

Jake Bowen Mirage neck and bridge master-switch wiring

Mirage rail single neck · Mirage humbucker bridge · EP1112 5-way master switch · One volume

DiMarzio Jake Bowen signature wiring: a Mirage rail single in the neck and a Mirage humbucker in the bridge on a 4-pole 5-way master switch with a 500K custom-taper volume. Positions: neck, neck parallel, neck & bridge, inner coils, bridge.

Viewed from the back of the controls, as you solder them.

Jake Bowen Mirage neck and bridge master-switch wiringJake Bowen Mirage neck and bridge master-switch wiring: Mirage rail single neck · Mirage humbucker bridge · EP1112 5-way master switch · One volume. Original Tinkercaster drawing with labelled terminals.Neck pickup (Mirage neck DP435)Bridge pickup (Mirage bridge DP434)500kblackwhiteredgreenbareredgreenwhiteblackbareT1T2T3T4T5T6T7T8T9T10T11T12T13T14T15T16T17T18T19T20T21T22T23T24lug1lug2lug3tipsleevegroundNeck pickup (Mirage neck DP435)Bridge pickup (Mirage bridge DP434)5-way master switch (EP1112)Volume 500K custom taperOutput jackTo bridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck pickup (Mirage neck DP435)Source: Neck pickup Mirage™ Neck DP435—Mirage™ NeckAs specified
Bridge pickup (Mirage bridge DP434)Source: Bridge pickup Mirage™ Bridge DP434—Mirage™ BridgeAs specified
5-way master switch (EP1112)Source: 5-way 'Master Switch' for Strat multipole EP1112—Oak Grigsby 4-Pole 5-Way Super SwitchExample part
Volume 500K custom taperSource: Volume 500K custom taper pot EP1201500kCTS 500k Audio PotExample part
Output jackSource: Switchcraft output jack (2-conductor) EP1301—Switchcraft #11Example part
To bridge ground—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All DiMarzio wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck greenVolume casing (top)To a pot casinggreen
2Neck bareVolume casing (top)Grey line beside the neck green.Shield or groundbare
3Upper row, left group, 4th lugVolume casing (bottom)Grey wire up from the switch.To a pot casing
4Bridge blackVolume casing (left)To a pot casingblack
5Bridge bareVolume casing (left)Grey line above the bridge black.Shield or groundbare
6Lower row, right group, 1st lugLower row, right group, 3rd lugGrey jumper over the 2nd lug.Wire
7Bridge greenLower row, right group, 2nd lugLoops under the switch beside the bridge red.Wiregreen
8Volume top lugVolume casing (top)To a pot casingblack
9Volume top lugJack sleeveRuns along the top and down the right edge of the sheet.Wireblack
10To bridge groundJack sleeveWireblack
11Neck blackUpper row, far-left lugDrawn broken where it passes behind the bridge leads.Wireblack
12Neck whiteUpper row, left group, 3rd lugDrawn broken where it passes behind the bridge leads.Wirewhite
13Upper row, left group, 3rd lugUpper row, left group, 5th lugThin black jumper under the lugs.Wireblack
14Upper row, left group, 5th lugUpper row, right group, 2nd lugThin black jumper over the top of the switch.Wireblack
15Upper row, right group, 2nd lugLower row, right group, 4th lugThin black jumper between the rows.Wireblack
16Neck redUpper row, right group, 3rd lugDrawn broken where it passes behind the bridge leads.Wirered
17Upper row, right group, 3rd lugUpper row, right group, 4th lugRed jumper.Wirered
18Upper row, right group, 4th lugUpper row, right group, 5th lugRed jumper.Wirered
19Bridge whiteLower row, right group, 1st lugLoops under the switch.Wirewhite
20Bridge redLower row, right group, 2nd lugLoops under the switch.Wirered
21Upper row, far-right lugVolume bottom lugLight grey wire.Wire
22Upper row, far-right lugLower row, far-right lugLight grey jumper at the right end of the switch.Wire
23Volume middle lugJack tipGrey wire.Wire

What each position does

SettingThe sourceEngine result
Neck (sheet Position 1)Position 1 = Neck.Neck pickup (Mirage neck DP435) (both coils).
Neck parallel (sheet Position 2)Position 2 = Neck Parallel.Neck pickup (Mirage neck DP435) (coils in parallel).
Neck & bridge (sheet Position 3)Position 3 = Neck & Bridge.Neck pickup (Mirage neck DP435) (both coils) and Bridge pickup (Mirage bridge DP434) (both coils) in parallel.
Inner coils (sheet Position 4)Position 4 = Bridge & Middle (Inner Coils). The sheet has no middle pickup; the wiring puts one coil of the neck and one of the bridge on.Neck pickup (Mirage neck DP435) (split to one coil) and Bridge pickup (Mirage bridge DP434) (split to one coil) in parallel.
Bridge (sheet Position 5)Position 5 = Bridge.Bridge pickup (Mirage bridge DP434) (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The Mirage rail single neck and Mirage bridge are drawn as their Mirage catalog parts; the rail construction is not modelled.
  • The 500K custom-taper volume is modelled by the catalog 500k audio pot; the simulator treats the taper as linear.
  • The bridge humbucker is wired with red and green joined as the link between its coils, white to the switch and black to ground, and the neck's black/white link is opened and closed by the switch. The editor checks recognise this reversed-lead wiring (hot and return leads joined as the link).

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • In each switch position, the meter across the jack should read the pickup or coil combination the legend names.
  • In Position 2 the neck black should read continuity to ground.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.