Skip to content
Tinkercaster

Seymour Duncan wiring

Two humbuckers, super switch (split to outer coils), volume and tone

Two humbuckers · Super 5-way blade · Split to outer coils · One volume · One tone

Seymour Duncan sheet: two humbuckers on a 4-pole super 5-way blade with a 500k volume, a 500k tone and a .047 cap. Positions 2 and 4 split the bridge and the neck to their outer coils; position 3 runs both humbuckers full.

Viewed from the back of the controls, as you solder them.

Two humbuckers, super switch (split to outer coils), volume and toneTwo humbuckers, super switch (split to outer coils), volume and tone: Two humbuckers · Super 5-way blade · Split to outer coils · One volume · One tone. Original Tinkercaster drawing with labelled terminals.Neck PickupBridge Pickup500k500k47nFblackgreenwhiteredbareblackgreenwhiteredbareT1T2T3T4T5T6T7T8T9T10T11T12T13T14T15T16T17T18T19T20T21T22T23T24lug1lug2lug3lug1lug2lug3tipsleeveabgroundNeck PickupBridge PickupSuper 5-Way BladeVolume 500kTone 500kOutput Jack.047 cap · 47nFBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck Pickup—Jazz Model SH-2 NeckExample partSame wiring for '59 Model SH-1 Neck, Duncan Distortion SH-6 Neck, Invader SH-8 Neck, Pearly Gates SH-PG1 Neck, Seymour Duncan SH-3 Stag Mag, Duncan Custom SH-5
Bridge Pickup—JB Model SH-4Example partSame wiring for '59 Model SH-1 Bridge, Duncan Custom SH-5, Duncan Distortion SH-6 Bridge, Invader SH-8 Bridge, Custom Five SH-14, Seymour Duncan SH-3 Stag Mag
Super 5-Way BladeSource: Super 5 way blade—Oak Grigsby 4-Pole 5-Way Super SwitchExample part
Volume 500k500kCTS 500k Audio PotExample part
Tone 500k500kCTS 500k Audio PotExample part
Output Jack—Switchcraft #11Example part
.047 cap47nFOrange Drop .047µFExample part
Bridge groundSource: Bridge ground wire—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck greenTop row, right group, 4th lugWith the neck black.Wiregreen
2Neck whiteVolume casing (upper Solder spot)To a pot casingwhite
3Neck bareVolume casing (upper Solder spot)Drawn grey beside the white.Shield or groundbare
4Bridge greenBottom row, right group, 2nd lugWith the bridge black.Wiregreen
5Bridge whiteVolume casing (upper Solder spot)To a pot casingwhite
6Bridge bareVolume casing (upper Solder spot)Drawn grey beside the white.Shield or groundbare
7Bottom row, far-right lugVolume casing (upper Solder spot)Runs down the right side to the volume.To a pot casingblack
8Volume third lugVolume casing (lower Solder spot)The lower Solder spot is drawn on this lug and the casing.To a pot casing
9.047 capTone casing (Solder spot)To a pot casing
10Volume casing (lower Solder spot)Tone casing (Solder spot)To a pot casingblack
11Tone casing (Solder spot)Jack sleeveWireblack
12Bridge ground wireTone casing (Solder spot)To a pot casingblack
13Neck redTop row, left group, 3rd lugRuns over the top of the switch.Wirered
14Top row, left group, 3rd lugTop row, left group, 4th lugJumper arch.Wirered
15Top row, left group, 4th lugTop row, left group, 5th lugJumper arch.Wirered
16Neck blackTop row, right group, 4th lugWith the neck green.Wireblack
17Bridge redBottom row, left group, 1st lugLeaves the bridge cable and runs up to the switch.Wirered
18Bottom row, left group, 1st lugBottom row, left group, 2nd lugJumper arch.Wirered
19Bottom row, left group, 2nd lugBottom row, left group, 3rd lugJumper arch.Wirered
20Bridge blackBottom row, right group, 2nd lugWith the bridge green.Wireblack
21Top row, far-left lugBottom row, far-left lugShort jumper down the left end of the switch.Wireblack
22Bottom row, far-left lugVolume first lugHops over the bridge cable on the way down.Wireblack
23Top row, far-right lugBottom row, far-right lugShort jumper down the right end of the switch.Wireblack
24Volume middle lugJack tipWireblack
25Volume first lugTone left lugWireblack
26Tone middle lug.047 capWireblack

What each position does

SettingThe sourceEngine result
Bridge full humbuckerNo legend printed; the bridge red is the only lug live in position 1 and its black/green link is open.Bridge Pickup (both coils).
Bridge split to outer coilNo legend printed; the bridge black/green lug is grounded in position 2, leaving the red-green coil ('Split to outer coils').Bridge Pickup (split to one coil).
Bridge + neck full humbuckersNo legend printed; both reds are live in position 3 and neither link is grounded.Neck Pickup (both coils) and Bridge Pickup (both coils) in parallel.
Neck split to outer coilNo legend printed; the neck black/green lug is grounded in position 4 ('Split to outer coils').Neck Pickup (split to one coil).
Neck full humbuckerNo legend printed; only the neck red is live in position 5.Neck Pickup (both coils).

Not simulated: this circuit is drawn for reference only.

  • Both humbuckers are drawn as their catalog parts (Jazz Model SH-2 neck, JB Model SH-4 bridge); which coil a split keeps (inner or outer) depends on mounting and is reported only as a split.
  • Pot tapers are not printed; the simulator treats the 500k pots as audio parts from the catalog.
  • Pickup resistance is not specified, so no numeric meter readings are given.
  • Each humbucker is wired with red as the output, black and green joined as the link between its coils and white to ground, so the catalog lead roles (black = hot, green = ground, white/red = series link) do not describe this wiring. The editor checks recognise this reversed-lead wiring (hot and return leads joined as the link).
  • The sheet prints no position legend, so the selection check has no oracle and the expected states are read from the drawn wiring.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • In each switch position, the meter across the jack should read the humbucker or single coil the position selects.
  • In positions 2 and 4 the split pickup's link lug should read continuity to ground.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.