Skip to content
Tinkercaster

DiMarzio · The wiring reference

DiMarzio series/parallel (Dual Sound) wiring

One switch, two humbucking sounds: full power in series, cleaner and brighter in parallel. Here is the lug-by-lug wiring from DiMarzio's sheet.

Applies to

DiMarzio four-conductor pickups with side-by-side coils, on a DPDT mini-switch (DiMarzio EP1106) or a push-pull pot (EP1200PP or EP1201PP). Lug numbers are the ones printed on DiMarzio's drawing.

Two sounds, both hum-cancelling

DiMarzio calls this wiring Dual Sound. In series the two coils work one after the other, for maximum power. In parallel they work side by side: the sheet describes that sound as slightly less powerful, with more highs and cleaner overall.

Parallel is not the same as a coil split. A split turns a coil off and the pickup stops cancelling hum. Dual Sound wiring cancels hum in both positions.

Parallel without a switch

If you only ever want the parallel sound, no switch is needed. Join red and white: that is the hot connection. Join green and black: that is the ground connection. The bare wire goes to ground as always.

Parallel without a switch
WiringHotJoined and tapedGround
Series (standard)RedBlack + whiteGreen, bare
ParallelRed + whiteNothingGreen + black, bare
Wire the Dual Sound switch

DiMarzio numbers the six lugs of the DPDT switch: 3, 2 and 1 along one row, 6, 5 and 4 along the other, so that 1 sits beside 4. All four pickup wires go to the switch. Lug 6 stays empty.

Do not skip the jumper between lugs 3 and 5. Without it the series position has no connection between the coils and the pickup is silent.

Wire the Dual Sound switch
Switch lugWhat connects there
1Red wire, and the wire to hot output
2White wire
3Jumper to lug 5
4Green wire, and the wire to ground
5Black wire, and the jumper from lug 3
6Nothing
  1. Solder a short jumper between lugs 3 and 5.
  2. Solder white to lug 2 and black to lug 5.
  3. Solder red to lug 1, with a wire from lug 1 to wherever the old pickup's hot wire went.
  4. Solder green to lug 4, with a wire from lug 4 to ground.
  5. Solder the bare wire to ground.
If the pickup needs reversed phase

The sheet gives the change in one line: use lug 4 as the hot output and connect lug 1 to ground. The bare wire is still soldered to ground.

Three sounds: series, single coil, parallel

Wire the same diagram on a three-position on-on-on DPDT mini-switch (DiMarzio EP1108) and you get a third sound. The two outside positions are series and parallel. The centre position is single coil.

See it in a complete guitar

This DiMarzio diagram puts series/parallel switching on the push-pull tone pots of a Les Paul style guitar. The six lugs under each pot are the switch described above.

Viewed from the back of the controls, as you solder them.

Les Paul series/parallel wiring with push/pull tones (661)DiMarzio's Les Paul series/parallel wiring: two volumes, two 500k push/pull tones with 50s-style capacitors. Pulling a tone knob switches that humbucker's coils from series to parallel.Neck pickupBridge pickup500k500k22nF500k500k22nFredgreenblackwhitebareredgreenblackwhitebareT1T2T3T4T5lug1lug2lug3lug1lug2lug3sw1sw2sw3sw4sw5sw6ablug1lug2lug3lug1lug2lug3sw1sw2sw3sw4sw5sw6abtipsleevegroundNeck pickupBridge pickupToggle (straight / straight short)Neck volume 500K custom taperNeck tone 500K push/pullNeck .022µFBridge volume 500K custom taperBridge tone 500K push/pullBridge .022µFOutput jackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Open the full page for this diagram →

Source and interpretation

Original explanation by Tinkercaster, based on DiMarzio 4-Conductor Pickup Instructions. The guide describes the stated configuration; it does not establish compatibility with every pickup or switch.

Not affiliated with or endorsed by DiMarzio. Refer to your exact pickup's instructions when a detail differs.

See it in a complete diagram

Put it in a complete circuit

Use a complete wiring diagram to see how the pickup, controls and output connect. Our public diagrams are free to view and explore.

Browse DiMarzio diagrams →

Understand this wiring

All DiMarzio wiring guides →