Skip to content
Tinkercaster

DiMarzio · The wiring reference

DiMarzio treble bleed and pot values

Keep the highs when you turn down, and choose between 250K, 500K and 1 Meg pots, using the values DiMarzio publishes.

Applies to

Passive DiMarzio pickups with ordinary volume and tone pots. The capacitor and resistor values are DiMarzio's own recommendations.

Stop the highs fading as you turn down

Many players notice the sound getting duller as the volume knob comes down. DiMarzio calls its fix treble compensation: a small capacitor across the volume pot lets the high frequencies through.

The sheet's recipe is a 560 pF capacitor, either alone or with a 300K ohm resistor beside it (270K or 330K also work). Both parts go in parallel across the two hot legs of the volume pot, meaning the lug the pickup signal arrives on and the lug it leaves from. The third lug is the one soldered to ground and is left alone.

Stop the highs fading as you turn down
PartValueNotes
Capacitor560 pFWorks alone
Resistor (optional)300K ohm270K or 330K also work
  1. Find the two hot lugs of the volume pot: signal in and signal out.
  2. Solder the 560 pF capacitor from one hot lug to the other.
  3. If you are adding the resistor, solder it across the same two lugs.
  4. Solder cleanly onto the lugs without disturbing the joints already there.
250K, 500K or 1 Meg

DiMarzio's FAQ puts the rule simply: whatever the pickups, a higher pot value gives a little more power and treble. Whether that is good is a matter of taste.

For humbuckers the sheet calls 500K the most common value for both volume and tone. 250K controls give a little warmer sound and a slight drop in power. A 1 Megohm tone control (DiMarzio EP1202) slightly increases treble and power, and can be combined with either a 250K or a 500K volume.

The FAQ adds that mixing values will not damage your pickups or your amp, and that single coil equals 250K, humbucker equals 500K is a habit from early Fender and Gibson guitars, not a rule.

250K, 500K or 1 Meg
ControlValueWhat DiMarzio says
Volume and tone500KMost common with humbuckers
Volume and tone250KA little warmer, slight drop in power
Tone1 Meg (EP1202)Slightly more treble and power
Tone capacitor.022 µFDiMarzio's recommended value
While the cavity is open: shielding

The sheet notes that all DiMarzio pickups are wax potted to stop squeal. For further noise reduction it recommends shielding the inside of the guitar with shielding tape (DiMarzio EP1000), which removes stray hum picked up by the wiring itself.

See it in a complete guitar

This DiMarzio diagram includes a treble bleed on the volume pot. Look for the small capacitor bridging two of the pot's lugs.

Viewed from the back of the controls, as you solder them.

Andy Timmons AT model: three humbuckers on a five-way Super SwitchDiMarzio's Andy Timmons (Ibanez AT) harness: Cruiser Bridge pickups in the neck and middle and an AT-1 in the bridge on a four-pole five-way Super Switch. The bridge splits when it is paired with the middle. A 500K custom-taper volume carries a 330pF capacitor; one 500K tone serves the neck and middle, a second serves the bridge alone, each with a .022 µF capacitor.Neck pickup (Cruiser Bridge DP187)Middle pickup (Cruiser Bridge DP187)Bridge pickup (AT-1 DP224)500k500k500k0.33nF22nF22nFredgreenblackwhitebareredgreenblackwhitebareredgreenblackwhitebareT1T2T3T4T5T6T7T8T9T10T11T12T13T14T15T16T17T18T19T20T21T22T23T24lug1lug2lug3lug1lug2lug3lug1lug2lug3abababtipsleevegroundNeck pickup (Cruiser Bridge DP187)Middle pickup (Cruiser Bridge DP187)Bridge pickup (AT-1 DP224)5-way Super SwitchVolume 500K custom taperNeck/middle tone 500K custom taperBridge tone 500K custom taper330pF.022µF.022µFOutput jackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Open the full page for this diagram →

Source and interpretation

Original explanation by Tinkercaster, based on DiMarzio 4-Conductor Pickup Instructions and the DiMarzio Product FAQ. The guide describes the stated configuration; it does not establish compatibility with every pickup or switch.

Not affiliated with or endorsed by DiMarzio. Refer to your exact pickup's instructions when a detail differs.

See it in a complete diagram

Put it in a complete circuit

Use a complete wiring diagram to see how the pickup, controls and output connect. Our public diagrams are free to view and explore.

Browse DiMarzio diagrams →

Understand this wiring

All DiMarzio wiring guides →