Skip to content
Tinkercaster

DiMarzio wiring

Richie Kotzen four-way Telecaster wiring

Single-coil neck, humbucker bridge · Four-way blade · One volume · One tone

DiMarzio Richie Kotzen Tele harness: Twang King neck and Chopper T bridge on a four-way blade with 250K custom-taper pots and a .022 µF capacitor. Sheet order is bridge / parallel / series / neck.

Viewed from the back of the controls, as you solder them.

Richie Kotzen four-way Telecaster wiringRichie Kotzen four-way Telecaster wiring: Single-coil neck, humbucker bridge · Four-way blade · One volume · One tone. Original Tinkercaster drawing with labelled terminals.Twang King neckChopper T bridge250k250k22nFwhiteblackgreyredgreenblackwhitebareT1T2T3T4T5T6T7T8T9T10lug1lug2lug3lug1lug2lug3abtipsleevegroundTwang King neckChopper T bridgeFour-way switchVolume 250K custom taperTone 250K custom taper.022µFOutput jackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Twang King neckSource: Twang King Neck DP172—DiMarzio Twang King Neck DP172As specified
Chopper T bridgeSource: The Chopper T Bridge DP384—DiMarzio The Chopper T DP384As specified
Four-way switch—4-Way Tele Mod SwitchExample part
Volume 250K custom taperSource: Volume 250K custom taper EP1200250kCTS 250k Audio PotExample part
Tone 250K custom taperSource: Tone 250K custom taper EP1200250kCTS 250k Audio PotExample part
.022µF22nFOrange Drop .022µFExample part
Output jack—Switchcraft #11Example part
Bridge ground—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All DiMarzio wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Twang King neck hotVolume 250K custom taper casingWirewhite
2Twang King neck gndFour-way switch T1Wireblack
3Chopper T bridge gndFour-way switch T5Wiregreen
4Chopper T bridge bareVolume 250K custom taper casingWirebare
5Four-way switch T9Four-way switch T8Wireground
6Four-way switch T8Volume 250K custom taper casingWireground
7Volume 250K custom taper lug1Volume 250K custom taper casingWireblack
8Volume 250K custom taper lug1Tone 250K custom taper casingWireblack
9.022µF bTone 250K custom taper casingWireyellow
10Tone 250K custom taper casingOutput jack sleeveWireblack
11Bridge ground groundOutput jack sleeveWireblack
12Twang King neck greyVolume 250K custom taper casingThe gray shield lead goes to ground on the volume casing.Wiregrey
13Chopper T bridge hotFour-way switch T10Wirered
14Four-way switch T1Four-way switch T3Wireblack
15Four-way switch T3Four-way switch T7Wireblack
16Four-way switch T5Volume 250K custom taper lug3Wiresignal
17Chopper T bridge blackChopper T bridge whiteWireblack
18Volume 250K custom taper lug2Output jack tipWiresignal
19Volume 250K custom taper lug3Tone 250K custom taper lug2Wirewhite
20Tone 250K custom taper lug1.022µF aWireyellow

What each position does

SettingThe sourceEngine result
BridgeEngine reading with KOTZEN_ORDER; matches the sheet legend (bridge / parallel / series / neck).Chopper T bridge (both coils).
Bridge + neck parallelEngine reading with KOTZEN_ORDER; matches the sheet legend (bridge / parallel / series / neck).Twang King neck and Chopper T bridge (both coils) in parallel.
Bridge + neck seriesEngine reading with KOTZEN_ORDER; matches the sheet legend (bridge / parallel / series / neck).Twang King neck and Chopper T bridge (both coils) in series.
NeckEngine reading with KOTZEN_ORDER; matches the sheet legend (bridge / parallel / series / neck).Twang King neck.

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Custom taper pots are treated as linear by the simulator.
  • FENDER_ORDER does not match this sheet's series-before-neck order.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.