Skip to content
Tinkercaster

Seymour Duncan wiring

Telecaster humbucker bridge, single neck, four-way

Viewed from the back of the controls, as you solder them.

Telecaster humbucker bridge, single neck, four-wayTelecaster humbucker bridge, single neck, four-way: Telecaster humbucker bridge, single neck, four-way. Original Tinkercaster drawing with labelled terminals.Neck humbuckerBridge single coil250k250k47nFblackgreenwhiteredbarewhiteblackT1T2T3T4T5T6T7T8T9T10lug1lug2lug3lug1lug2lug3abtipsleevegroundNeck humbuckerBridge single coil4-Way SwitchVolume 250kTone 250k.047 cap · 47nFOutput JackGround wire from bridge

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck humbucker—Jazz Model SH-2 NeckExample partSame wiring for '59 Model SH-1 Neck, Seymour Duncan Antiquity Neck, Pearly Gates SH-PG1 Neck, Invader SH-8 Neck, Duncan Distortion SH-6 Neck, Alnico II Pro APH-1 Neck
Bridge single coil—Vintage '54 Tele Lead STL-1Example partSame wiring for Vintage Tele Rhythm STR-1, Vintage Staggered Strat SSL-1, Vintage Flat Strat SSL-2, Quarter-Pound Flat Strat SSL-4, Custom SSL-5
4-Way Switch—4-Way Tele Mod SwitchExample part
Volume 250k250kCTS 250k Audio PotExample part
Tone 250k250kCTS 250k Audio PotExample part
.047 cap47nFOrange Drop .047µFExample part
Output Jack—Switchcraft #11Example part
Ground wire from bridge—Bridge ground wireExample part

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck humbucker gnd4-Way Switch T5Wiregreen
2Neck humbucker bareVolume 250k casingWirebare
3Bridge single coil gndVolume 250k casingWireblack
44-Way Switch T3Volume 250k casingWireblack
5Ground wire from bridge groundVolume 250k casingWireblack
6Volume 250k lug1Volume 250k casingWireground
7.047 cap bTone 250k casingWireblack
8Volume 250k casingTone 250k casingWireblack
9Tone 250k casingOutput Jack sleeveWireblack
10Neck humbucker hot4-Way Switch T6Wireblack
11Bridge single coil hot4-Way Switch T10Wirewhite
124-Way Switch T24-Way Switch T3Wireblack
134-Way Switch T64-Way Switch T7Wireblack
144-Way Switch T7Volume 250k lug3Wireblack
154-Way Switch T44-Way Switch T9Wireblack
16Neck humbucker redNeck humbucker whiteWirered
17Volume 250k lug2Output Jack tipWireblack
18Volume 250k lug3Tone 250k lug1Wireblack
19Tone 250k lug2.047 cap aWireblack

What each position does

SettingThe sourceEngine result
Position 1Engine reading of the transcribed board; matches the source legend.Bridge single coil.
Position 2Engine reading of the transcribed board; matches the source legend.Neck humbucker (both coils) and Bridge single coil in parallel.
Position 3Engine reading of the transcribed board; matches the source legend.Neck humbucker (both coils).
Position 4Engine reading of the transcribed board; matches the source legend.Neck humbucker (both coils) and Bridge single coil in series.

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Custom tapers are not reproduced; pots are simulated as linear.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.