Skip to content
Tinkercaster

Seymour Duncan wiring

Telecaster Tele stack and single coil, four-way

Tele stack neck, single-coil bridge · Four-way blade · One volume · One tone

A neck Tele stack and a bridge single coil on a four-way blade, one 250k volume and one 250k tone with a .047 µF capacitor. Position 4 runs both pickups in series.

Viewed from the back of the controls, as you solder them.

Telecaster Tele stack and single coil, four-wayTelecaster Tele stack and single coil, four-way: Tele stack neck, single-coil bridge · Four-way blade · One volume · One tone. Original Tinkercaster drawing with labelled terminals.Neck single coilBridge Tele stack250k250k47nFwhiteblackblackwhiteredgreenbareT1T2T3T4T5T6T7T8T9T10lug1lug2lug3lug1lug2lug3abtipsleevegroundgroundNeck single coilBridge Tele stack4-Way SwitchVolume 250kTone 250k.047 cap · 47nFOutput JackGround wire from bridgeNeck pickup cover ground wire

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck single coil—Vintage Tele Rhythm STR-1Example partSame wiring for Vintage Staggered Strat SSL-1, Custom SSL-5
Bridge Tele stack—Seymour Duncan Vintage Stack for Tele BridgeExample part
4-Way Switch—4-Way Tele Mod SwitchExample part
Volume 250k250kCTS 250k Audio PotExample part
Tone 250k250kCTS 250k Audio PotExample part
.047 cap47nFOrange Drop .047µFExample part
Output Jack—Switchcraft #11Example part
Ground wire from bridge—Bridge ground wireGeneric
Neck pickup cover ground wire—Pickup cover ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck single coil black4-Way Switch T5Wireblack
2Bridge Tele stack bareVolume 250k casingWirebare
3Bridge Tele stack greenVolume 250k casingWiregreen
44-Way Switch T3Volume 250k casingWireblack
5Ground wire from bridge groundVolume 250k casingWireblack
6Volume 250k lug1Volume 250k casingWireground
7.047 cap bTone 250k casingWireblack
8Volume 250k casingTone 250k casingWireblack
9Tone 250k casingOutput Jack sleeveWireblack
10Neck pickup cover ground wire groundVolume 250k casingThe neck pickup cover is grounded with its own wire, as the sheet prints.Wireblack
11Neck single coil white4-Way Switch T6Wirewhite
12Bridge Tele stack black4-Way Switch T10Wireblack
134-Way Switch T24-Way Switch T3Wireblack
144-Way Switch T64-Way Switch T7Wireblack
154-Way Switch T7Volume 250k lug3Wireblack
164-Way Switch T44-Way Switch T9Wireblack
17Bridge Tele stack redBridge Tele stack whiteRed & white joined and taped off.Wirered
18Volume 250k lug2Output Jack tipWireblack
19Volume 250k lug3Tone 250k lug1Wireblack
20Tone 250k lug2.047 cap aWireblack

What each position does

SettingThe sourceEngine result
Bridge1. bridge pickupBridge Tele stack (both coils).
Bridge and neck in parallel2. bridge & neck pickups parallelNeck single coil and Bridge Tele stack (both coils) in parallel.
Neck3. neck pickupNeck single coil.
Bridge and neck in series4. bridge & neck in series (higher output and beefier tone)Neck single coil and Bridge Tele stack (both coils) in series.

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Pickup resistance is not specified, so no numeric meter readings are given.
  • Stacked single-coil construction is not modelled beyond the two-coil series link.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.