Skip to content
Tinkercaster

DiMarzio wiring

Les Paul coil split (master tone push/pull)

Two humbuckers · Toggle · Two volumes · Two tones · Master split

DiMarzio's Les Paul coil split: two volumes, two tones, and a push/pull on the neck tone that splits both humbuckers at once, the bridge to its north coil and the neck to its south.

Viewed from the back of the controls, as you solder them.

Les Paul coil split (master tone push/pull)Les Paul coil split (master tone push/pull): Two humbuckers · Toggle · Two volumes · Two tones · Master split. Original Tinkercaster drawing with labelled terminals.Neck PickupBridge Pickup500k500k500k500k22nF22nFredgreenblackwhitebareredgreenblackwhitebareT1T2T3T4lug1lug2lug3lug1lug2lug3lug1lug2lug3sw1sw2sw3sw4sw5sw6lug1lug2lug3tipsleevegroundababNeck PickupBridge Pickup3-Way ToggleNeck Volume 500kABridge Volume 500kANeck tone 500K push/pull (master split)Bridge Tone 500kAOutput JackBridge ground.022µf (neck).022µf (bridge)

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck Pickup—PAF Pro DP151Example partSame wiring for PAF 36th Anniversary Neck DP103, DiMarzio Air Classic Neck DP190, The Humbucker From Hell DP156, Evolution Neck DP158, D Activator Neck DP219, PAF Master Neck (4-conductor)
Bridge Pickup—Super Distortion DP100Example partSame wiring for DiMarzio Dual Sound DP101, DiMarzio Super 2 DP104, DiMarzio DLX Plus Bridge DP154, DiMarzio Norton DP160, DiMarzio Steve's Special DP161, DiMarzio D Sonic DP207
3-Way Toggle—Switchcraft 3-Way ToggleExample part
Neck Volume 500kA500kCTS 500k Audio PotExample part
Bridge Volume 500kA500kCTS 500k Audio PotExample part
Neck tone 500K push/pull (master split)500k500k Push-Pull DPDTExample part
Bridge Tone 500kA500kCTS 500k Audio PotExample part
Output Jack—Switchcraft #11Example part
Bridge ground—Bridge ground wireGeneric
.022µf (neck)22nFOrange Drop .022µFExample part
.022µf (bridge)22nFOrange Drop .022µFExample part

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All DiMarzio wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck BLACK runs right and down to the neck volume casing.Neck BLACK runs right and down to the neck volume casing.Wireblack
2Neck BARE runs with it to the neck volume casing.Neck BARE runs with it to the neck volume casing.Wirebare
3Bridge GREEN runs right and down to the bridge volume casing.Bridge GREEN runs right and down to the bridge volume casing.Wiregreen
4Bridge BARE runs with the green to the bridge volume casing.Bridge BARE runs with the green to the bridge volume casing.Wirebare
5Neck tone 500K push/pull (master split) lug2Neck tone 500K push/pull (master split) casingWireground
6Bridge Tone 500kA lug2Bridge Tone 500kA casingWireground
7The neck volume's other outer lug carries a solder dot on the casing: soldered to the casing.The neck volume's other outer lug carries a solder dot on the casing: soldered to the casing.Wireground
8The bridge volume's other outer lug carries a solder dot on the casing: soldered to the casing.The bridge volume's other outer lug carries a solder dot on the casing: soldered to the casing.Wireground
9Black ground bus from the neck volume casing down to the bridge volume casing.Black ground bus from the neck volume casing down to the bridge volume casing.Wireground
10Black from the neck volume casing across to the push/pull tone casing.Black from the neck volume casing across to the push/pull tone casing.Wireground
11Black from the bridge volume casing across to the bridge tone casing.Black from the bridge volume casing across to the bridge tone casing.Wireground
12Black from the toggle's ground tag round the bottom to the jack sleeve; drawn here to the push/pull casing, the same ground.Black from the toggle's ground tag round the bottom to the jack sleeve; drawn here to the push/pull casing, the same ground.Wireground
13Black from the tone casings down the right side to the jack sleeve; drawn here to the bridge tone casing, the same ground.Black from the tone casings down the right side to the jack sleeve; drawn here to the bridge tone casing, the same ground.Wireground
14'TO BRIDGE GROUND' line.'TO BRIDGE GROUND' line.Wireground
15Neck GREEN runs with the red to the same push/pull middle lug.Neck GREEN runs with the red to the same push/pull middle lug.Wiregreen
16Black jumper from the push/pull lug nearest the pot on the neck row to the casing junction.Black jumper from the push/pull lug nearest the pot on the neck row to the casing junction.Wireblack
17The same black jumper takes in the bridge row's lug nearest the pot.The same black jumper takes in the bridge row's lug nearest the pot.Wireblack
18Neck Volume 500kA lug33-Way Toggle T1Wiresignal
19Bridge Volume 500kA lug33-Way Toggle T2Wiresignal
20Grey from the toggle's output tag to the jack tip.Grey from the toggle's output tag to the jack tip.Wiresignal
21Neck Pickup whiteNeck Volume 500kA lug2Wirewhite
22Bridge Pickup hotBridge Volume 500kA lug2Wirered
23Neck RED runs right, down and along to the push/pull's middle lug on the neck row.Neck RED runs right, down and along to the push/pull's middle lug on the neck row.Wirered
24Bridge WHITE runs down, along and up to the push/pull's middle lug on the bridge row.Bridge WHITE runs down, along and up to the push/pull's middle lug on the bridge row.Wirewhite
25Bridge BLACK runs with the white to the same push/pull middle lug.Bridge BLACK runs with the white to the same push/pull middle lug.Wireblack
26Neck Volume 500kA lug2.022µf (neck) aWirewhite
27.022µf (neck) bNeck tone 500K push/pull (master split) lug1Wirewhite
28Bridge Volume 500kA lug2.022µf (bridge) aWirewhite
29.022µf (bridge) bBridge Tone 500kA lug1Wirewhite

What each position does

SettingThe sourceEngine result
Toggle 1 · neck, neck tone pushedSheet note: 'Push/pull splits to the north coil on the bridge and the south on the neck.' The push/pull is the neck tone (NECK TONE PULL - COIL SPLIT); knob down is full humbucker.Neck Pickup (both coils).
Toggle 2 · both, neck tone pushedSheet note: 'Push/pull splits to the north coil on the bridge and the south on the neck.' The push/pull is the neck tone (NECK TONE PULL - COIL SPLIT); knob down is full humbucker.Neck Pickup (both coils) and Bridge Pickup (both coils) in parallel.
Toggle 3 · bridge, neck tone pushedSheet note: 'Push/pull splits to the north coil on the bridge and the south on the neck.' The push/pull is the neck tone (NECK TONE PULL - COIL SPLIT); knob down is full humbucker.Bridge Pickup (both coils).
Toggle 1 · neck, neck tone pulledSheet note: 'Push/pull splits to the north coil on the bridge and the south on the neck.' The push/pull is the neck tone (NECK TONE PULL - COIL SPLIT); knob down is full humbucker.Neck Pickup (split to one coil).
Toggle 2 · both, neck tone pulledSheet note: 'Push/pull splits to the north coil on the bridge and the south on the neck.' The push/pull is the neck tone (NECK TONE PULL - COIL SPLIT); knob down is full humbucker.Neck Pickup (split to one coil) and Bridge Pickup (split to one coil) in parallel.
Toggle 3 · bridge, neck tone pulledSheet note: 'Push/pull splits to the north coil on the bridge and the south on the neck.' The push/pull is the neck tone (NECK TONE PULL - COIL SPLIT); knob down is full humbucker.Bridge Pickup (split to one coil).

Not simulated: this circuit is drawn for reference only.

  • The engine reports a split coil as split; it does not say which coil of the pair stays on, so the north/south choice is checked by the lead assignments in the notes, not by the engine.
  • Custom pot tapers are simulated as linear audio tracks.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.