Skip to content
Tinkercaster

Seymour Duncan wiring

Two P-Rails, toggle, two volumes, two tones, push/pull split

2 P-Rails · toggle · 2V · 2T · tone push/pull split

Transcribed from the manufacturer wiring sheet.

Viewed from the back of the controls, as you solder them.

Two P-Rails, toggle, two volumes, two tones, push/pull splitTwo P-Rails, toggle, two volumes, two tones, push/pull split: 2 P-Rails · toggle · 2V · 2T · tone push/pull split. Original Tinkercaster drawing with labelled terminals.Neck pickupBridge pickup500k500k500k500k47nF47nFblackgreenwhiteredbareblackgreenwhiteredbareT1T2T3T4lug1lug2lug3lug1lug2lug3tipsleevegroundlug1lug2lug3sw1sw2sw3sw4sw5sw6lug1lug2lug3sw1sw2sw3sw4sw5sw6ababNeck pickupBridge pickup3-way toggleBridge volume · 500kNeck volume · 500kOutput jackBridge groundNeck tone push/pull · 500kBridge tone push/pull · 500kNeck .047 cap · 47nFBridge .047 cap · 47nF

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck pickup—Seymour Duncan P-RailsAs specified
Bridge pickup—Seymour Duncan P-RailsAs specified
3-way toggle—Switchcraft 3-Way ToggleExample part
Bridge volume500kNot on the sheet; stand-inCTS 500k Audio PotExample part
Neck volume500kNot on the sheet; stand-inCTS 500k Audio PotExample part
Output jack—Switchcraft #11Example part
Bridge ground—Bridge ground wireGeneric
Neck tone push/pull500kNot on the sheet; stand-in500k Push-Pull DPDTExample part
Bridge tone push/pull500kNot on the sheet; stand-in500k Push-Pull DPDTExample part
Neck .047 cap47nFOrange Drop .047µFExample part
Bridge .047 cap47nFOrange Drop .047µFExample part

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck pickup gndNeck tone push/pull sw1Wiregreen
2Neck pickup bareNeck tone 500k push/pull casingWirebare
3Neck volume 500k lug1Neck volume 500k casingWireground
4Neck .047 cap bNeck tone 500k push/pull casingWireblack
5Neck tone 500k push/pull casingNeck volume 500k casingWireground
6Bridge pickup gndNeck tone push/pull sw4Wiregreen
7Bridge pickup bareNeck tone push/pull casingWirebare
8Bridge volume 500k lug1Bridge volume 500k casingWireground
9Bridge .047 cap bBridge tone 500k push/pull casingWireblack
10Neck tone push/pull sw1Neck tone push/pull sw4Wireground
11Bridge tone 500k push/pull casingBridge volume 500k casingWireground
123-way toggle T4Neck volume 500k casingWireground
13Bridge volume 500k casingNeck volume 500k casingWireground
14Bridge ground groundBridge volume 500k casingWireground
15Neck volume 500k casingOutput jack sleeveWireground
16Neck tone push/pull sw1Neck tone push/pull casingWireground
17Neck volume 500k lug23-way toggle T1Wireblack
18Bridge volume 500k lug23-way toggle T2Wireblack
193-way toggle T3Output jack tipWiresignal
20Neck pickup hotNeck volume 500k lug3Wireblack
21Neck pickup whiteNeck tone push/pull sw2Wirewhite
22Neck pickup redBridge tone push/pull sw2Wirered
23Bridge tone push/pull sw1Neck pickup hotWireblack
24Bridge pickup hotBridge volume 500k lug3Wireblack
25Bridge pickup whiteNeck tone push/pull sw5Wirewhite
26Bridge pickup redBridge tone push/pull sw5Wirered
27Bridge tone push/pull sw4Bridge pickup hotWireblack
28Neck volume lug3Neck tone push/pull lug1Wireblack
29Neck tone 500k push/pull lug2Neck .047 cap aWireblack
30Bridge volume lug3Bridge tone push/pull lug1Wireblack
31Bridge tone 500k push/pull lug2Bridge .047 cap aWireblack
32Bridge tone 500k push/pull sw3Neck tone 500k push/pull sw3Coil-split joint: the two tone pots' down contacts meet here (Neck black-finish/white-finish series path).Wireblack
33Bridge tone 500k push/pull sw6Neck tone 500k push/pull sw6Coil-split joint: the two tone pots' down contacts meet here for the bridge pickup.Wireblack

What each position does

SettingThe sourceEngine result
Position 1 Neck: Parallel (both coils on)Engine reading of the transcribed board; matches the source sheet's table.Neck pickup (coils in parallel).
Position 1 Neck: P-90 coils selected (rails shut off)Engine reading of the transcribed board; matches the source sheet's table.Neck pickup (split to one coil).
Position 1 Neck: Rail coils selected (P-90s shut off)Engine reading of the transcribed board; matches the source sheet's table.Neck pickup (split to one coil).
Position 1 Neck: Series (both coils on)Engine reading of the transcribed board; matches the source sheet's table.Neck pickup (both coils).
Position 2 Neck + bridge: Parallel (both coils on)Engine reading of the transcribed board; matches the source sheet's table.Neck pickup (coils in parallel) and Bridge pickup (coils in parallel) in parallel.
Position 2 Neck + bridge: P-90 coils selected (rails shut off)Engine reading of the transcribed board; matches the source sheet's table.Neck pickup (split to one coil) and Bridge pickup (split to one coil) in parallel.
Position 2 Neck + bridge: Rail coils selected (P-90s shut off)Engine reading of the transcribed board; matches the source sheet's table.Neck pickup (split to one coil) and Bridge pickup (split to one coil) in parallel.
Position 2 Neck + bridge: Series (both coils on)Engine reading of the transcribed board; matches the source sheet's table.Neck pickup (both coils) and Bridge pickup (both coils) in parallel.
Position 3 Bridge: Parallel (both coils on)Engine reading of the transcribed board; matches the source sheet's table.Bridge pickup (coils in parallel).
Position 3 Bridge: P-90 coils selected (rails shut off)Engine reading of the transcribed board; matches the source sheet's table.Bridge pickup (split to one coil).
Position 3 Bridge: Rail coils selected (P-90s shut off)Engine reading of the transcribed board; matches the source sheet's table.Bridge pickup (split to one coil).
Position 3 Bridge: Series (both coils on)Engine reading of the transcribed board; matches the source sheet's table.Bridge pickup (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Coil split is topology-first; the P-90 and rail positions share one coil mode in the engine.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.