Skip to content
Tinkercaster

Tonerider wiring

Two humbuckers, toggle, push/pull split tone

Two humbuckers · Toggle · Push/pull tone split · Volume

Transcribed from the manufacturer wiring sheet and checked against the engine.

Viewed from the back of the controls, as you solder them.

Two humbuckers, toggle, push/pull split toneTwo humbuckers, toggle, push/pull split tone: Two humbuckers · Toggle · Push/pull tone split · Volume. Original Tinkercaster drawing with labelled terminals.Neck PickupBridge Pickup500k500k22nFredblackwhitegreenbareredblackwhitegreenbareT1T2T3T4lug1lug2lug3lug1lug2lug3sw1sw2sw3sw4sw5sw6tipsleeveabgroundNeck PickupBridge Pickup3-Way ToggleVolume 500kATone 500kA push/pullOutput Jack.022µfGround wire from bridge

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck Pickup—Tonerider Alnico 2 ClassicExample partSame wiring for Tonerider Alnico 4 Classic, Tonerider Rocksong
Bridge Pickup—Tonerider Alnico 2 ClassicExample partSame wiring for Tonerider Alnico 4 Classic, Tonerider Rocksong
3-Way Toggle—Switchcraft 3-Way ToggleExample part
Volume 500kA500kCTS 500k Audio PotExample part
Tone 500kA push/pull500k500k Push-Pull DPDTExample part
Output Jack—Switchcraft #11Example part
.022µf22nFOrange Drop .022µFExample part
Ground wire from bridge—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck black runs straight right to the big solder spot on the left of the volume casing.Neck black runs straight right to the big solder spot on the left of the volume casing.Wireblack
2Neck bare shield ('Bare Shield Wires' callout) runs with the black to the volume casing.Neck bare shield ('Bare Shield Wires' callout) runs with the black to the volume casing.Wirebare
3Neck green drops down and ends on the push/pull switch's left middle lug.Neck green drops down and ends on the push/pull switch's left middle lug.Wiregreen
4Bridge green runs up to the solder spot on the left of the volume casing.Bridge green runs up to the solder spot on the left of the volume casing.Wiregreen
5Bridge bare shield runs up beside the green to the volume casing.Bridge bare shield runs up beside the green to the volume casing.Wirebare
6Left switch lug nearest the pot body: black jumper up to the solder spot on the tone casing.Left switch lug nearest the pot body: black jumper up to the solder spot on the tone casing.Wireblack
7Right switch lug nearest the pot body: black jumper to the same tone-casing solder spot.Right switch lug nearest the pot body: black jumper to the same tone-casing solder spot.Wireblack
8The toggle's frame lug goes to a ground symbol; joined to the volume casing here.The toggle's frame lug goes to a ground symbol; joined to the volume casing here.Wireground
9Volume right lug is bent onto the casing (short black link).Volume right lug is bent onto the casing (short black link).Wireground
10The capacitor's other leg ends on a solder spot on the tone casing.The capacitor's other leg ends on a solder spot on the tone casing.Wireblack
11The tone casing goes to a ground symbol; joined to the volume casing here.The tone casing goes to a ground symbol; joined to the volume casing here.Wireground
12The jack's sleeve lug goes to a ground symbol; joined to the volume casing here.The jack's sleeve lug goes to a ground symbol; joined to the volume casing here.Wireground
13'Ground Wire from Bridge' ends on the right solder spot of the volume casing, which also goes to a ground symbol.'Ground Wire from Bridge' ends on the right solder spot of the volume casing, which also goes to a ground symbol.Wireground
14Neck white runs up and right to the toggle's upper outer lug (live in the neck position).Neck white runs up and right to the toggle's upper outer lug (live in the neck position).Wirewhite
15Bridge red runs up the left side to the toggle's lower outer lug (live in the bridge position).Bridge red runs up the left side to the toggle's lower outer lug (live in the bridge position).Wirered
16Grey wire from the toggle's middle lug down the right side and back left to the volume's left lug (back view, lugs down).Grey wire from the toggle's middle lug down the right side and back left to the volume's left lug (back view, lugs down).Wiresignal
17Neck red runs beside the green to the same left middle switch lug.Neck red runs beside the green to the same left middle switch lug.Wirered
18Bridge white runs right and ends on the push/pull switch's right middle lug.Bridge white runs right and ends on the push/pull switch's right middle lug.Wirewhite
19Bridge black runs beside the white to the same right middle switch lug.Bridge black runs beside the white to the same right middle switch lug.Wireblack
20Volume middle lug runs right to the jack's tip lug.Volume middle lug runs right to the jack's tip lug.Wiresignal
21Volume left lug drops straight down to the tone's left lug (tone drawn lugs up).Volume left lug drops straight down to the tone's left lug (tone drawn lugs up).Wiresignal
22Tone middle lug goes to one leg of the .022µf capacitor; the right tone lug is drawn empty.Tone middle lug goes to one leg of the .022µf capacitor; the right tone lug is drawn empty.Wireblack

What each position does

SettingThe sourceEngine result
Toggle 1 · neck, tone down (humbucker)Sheet legend: 'UP: Split (Neck Screw, Bridge Slug) ... DOWN: Full Humbucker Mode'. Toggle: neck white to the first tag, bridge red to the third, middle tag to the volume.Neck Pickup (both coils).
Toggle 2 · both, tone down (humbucker)Sheet legend: 'UP: Split (Neck Screw, Bridge Slug) ... DOWN: Full Humbucker Mode'. Toggle: neck white to the first tag, bridge red to the third, middle tag to the volume.Neck Pickup (both coils) and Bridge Pickup (both coils) in parallel.
Toggle 3 · bridge, tone down (humbucker)Sheet legend: 'UP: Split (Neck Screw, Bridge Slug) ... DOWN: Full Humbucker Mode'. Toggle: neck white to the first tag, bridge red to the third, middle tag to the volume.Bridge Pickup (both coils).
Toggle 1 · neck, tone pulled (split)Sheet legend: 'UP: Split (Neck Screw, Bridge Slug) ... DOWN: Full Humbucker Mode'. Toggle: neck white to the first tag, bridge red to the third, middle tag to the volume.Neck Pickup (split to one coil).
Toggle 2 · both, tone pulled (split)Sheet legend: 'UP: Split (Neck Screw, Bridge Slug) ... DOWN: Full Humbucker Mode'. Toggle: neck white to the first tag, bridge red to the third, middle tag to the volume.Neck Pickup (split to one coil) and Bridge Pickup (split to one coil) in parallel.
Toggle 3 · bridge, tone pulled (split)Sheet legend: 'UP: Split (Neck Screw, Bridge Slug) ... DOWN: Full Humbucker Mode'. Toggle: neck white to the first tag, bridge red to the third, middle tag to the volume.Bridge Pickup (split to one coil).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The neck humbucker is wired with WHITE as the hot and BLACK to ground, with RED and GREEN joined as its series link on the push/pull, as drawn. The DiMarzio-colour catalog part names GREEN the return and BLACK/WHITE the finishes. The editor checks recognise this reversed-lead wiring (hot and return leads joined as the link).
  • Which coil of each humbucker remains in split mode (screw or slug) is not modelled.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.