Skip to content
Tinkercaster

DiMarzio wiring

One humbucker, volume, tone, EP1108 on-on-on dual sound

One humbucker · Volume · Tone · DPDT on-on-on dual sound

Transcribed from the manufacturer wiring sheet and checked against the engine.

Viewed from the back of the controls, as you solder them.

One humbucker, volume, tone, EP1108 on-on-on dual soundOne humbucker, volume, tone, EP1108 on-on-on dual sound: One humbucker · Volume · Tone · DPDT on-on-on dual sound. Original Tinkercaster drawing with labelled terminals.Bridge humbucker500k500k22nFredgreenblackwhitebareT1T2T3T4T5T6lug1lug2lug3lug1lug2lug3abtipsleevegroundBridge humbuckerDPDT on-on-on dual soundVolume 500kTone 500k.022 µFOutput jackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Bridge humbucker—DiMarzio Dual Sound DP101As specified
DPDT on-on-on dual sound—DPDT Mini-Toggle (on-on-on)Example part
Volume 500k500kCTS 500k Audio PotExample part
Tone 500k500kCTS 500k Audio PotExample part
.022 µF22nFOrange Drop .022µFExample part
Output jack—Switchcraft #11Example part
Bridge ground—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All DiMarzio wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Bridge humbucker gndDPDT on-on-on dual sound T1Wiregreen
2Bridge humbucker bareVolume 500k casingWirebare
3DPDT on-on-on dual sound T1Volume 500k casingGround wire from the green lug to the volume casing.Wireblack
4Volume 500k lug1Volume 500k casingWireground
5.022 µF bTone 500k casingWireground
6Volume 500k casingTone 500k casingWireground
7Tone 500k casingOutput jack sleeveWireground
8Bridge ground groundOutput jack sleeveWireground
9Bridge humbucker hotDPDT on-on-on dual sound T4Wirered
10Bridge humbucker blackDPDT on-on-on dual sound T6Wireblack
11Bridge humbucker whiteDPDT on-on-on dual sound T5Wirewhite
12DPDT on-on-on dual sound T6DPDT on-on-on dual sound T2The black lead runs onto the top lug of the white pole and on to the middle lug of the other pole.Wireblack
13DPDT on-on-on dual sound T4Volume 500k lug3Wiresignal
14Volume 500k lug2Output jack tipWiresignal
15Volume 500k lug3Tone 500k middle lugWiresignal
16Tone 500k bottom lug.022 µF aWireyellow

What each position does

SettingThe sourceEngine result
Up: parallelLegend: UP = PARALLEL, CENTER = SPLIT, DOWN = SERIES.Bridge humbucker (coils in parallel).
Center: splitLegend: UP = PARALLEL, CENTER = SPLIT, DOWN = SERIES.Bridge humbucker (split to one coil).
Down: seriesLegend: UP = PARALLEL, CENTER = SPLIT, DOWN = SERIES.Bridge humbucker (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.