Skip to content
Tinkercaster

Seymour Duncan wiring

One humbucker, volume, mini-toggle series/split/parallel

One humbucker · On-on-on mini-toggle · Volume 500k

Transcribed from the manufacturer wiring sheet.

Viewed from the back of the controls, as you solder them.

One humbucker, volume, mini-toggle series/split/parallelOne humbucker, volume, mini-toggle series/split/parallel: One humbucker · On-on-on mini-toggle · Volume 500k. Original Tinkercaster drawing with labelled terminals.Bridge humbucker500kblackgreenwhiteredbareT1T2T3T4T5T6lug1lug2lug3tipsleevegroundBridge humbuckerSeries/split/parallel on-on-onVolume 500kOutput jackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Bridge humbucker—JB Model SH-4Example partSame wiring for Duncan Custom SH-5, Duncan Distortion SH-6 Bridge, Invader SH-8 Bridge, Seymour Duncan SH-2 Jazz Bridge, Seymour Duncan SH-3 Stag Mag, Custom Five SH-14
Series/split/parallel on-on-on—DPDT Mini-Toggle (on-on-on)Example part
Volume 500k500kCTS 500k Audio PotExample part
Output jack—Switchcraft #11Example part
Bridge ground—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Bridge humbucker gndSeries/split/parallel on-on-on T3Wiregreen
2Bridge humbucker bareSeries/split/parallel on-on-on T3Wirebare
3Series/split/parallel on-on-on T3Volume 500k casingWireblack
4Volume 500k lug1Volume 500k casingWireground
5Output jack sleeveVolume 500k casingWireblack
6Bridge ground groundVolume 500k casingWireblack
7Bridge humbucker hotSeries/split/parallel on-on-on T6Wireblack
8Bridge humbucker whiteSeries/split/parallel on-on-on T2Wirewhite
9Bridge humbucker redSeries/split/parallel on-on-on T5Wirered
10Series/split/parallel on-on-on T4Series/split/parallel on-on-on T2Top-right lug jumpered to the middle-left lug.Wireblack
11Series/split/parallel on-on-on T6Volume 500k lug3Wireblack
12Volume 500k lug2Output jack tipWireblack

What each position does

SettingThe sourceEngine result
Up: seriesLegend: Series (up), Split (middle), Parallel (down); the split keeps the slug coil.Bridge humbucker (both coils).
Middle: splitLegend: Series (up), Split (middle), Parallel (down); the split keeps the slug coil.Bridge humbucker (split to one coil).
Down: parallelLegend: Series (up), Split (middle), Parallel (down); the split keeps the slug coil.Bridge humbucker (coils in parallel).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Standalone mini-toggles use switchPosition; lever states share the selector index unless noted.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.