Skip to content
Tinkercaster

Seymour Duncan wiring

Esquire alternate wiring with a yellow tap on the bridge pickup

Esquire alt · 3-way · 1V · 1T · .047µF

The Esquire alternate wiring: a tapped bridge pickup on a 3-way blade. Position 1 is full output with tone, position 2 is the tap with tone, and position 3 is the tap with no tone.

Viewed from the back of the controls, as you solder them.

Esquire alternate wiring with a yellow tap on the bridge pickupEsquire alternate wiring with a yellow tap on the bridge pickup: Esquire alt · 3-way · 1V · 1T · .047µF. Original Tinkercaster drawing with labelled terminals.Bridge Esquire pickup250k250k47nFwhiteyellowblackT1T2T3T4T5T6T7T8lug1lug2lug3lug1lug2lug3abtipsleevegroundBridge Esquire pickup3-Way SwitchVolume 250kTone 250k.047 cap · 47nFOutput JackGround wire from bridge

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Bridge Esquire pickup—Seymour W. Duncan Signature Esquire BridgeExample part
3-Way Switch—CRL 3-Way BladeExample part
Volume 250k250kCTS 250k Audio PotExample part
Tone 250k250kCTS 250k Audio PotExample part
.047 cap47nFOrange Drop .047µFExample part
Output Jack—Switchcraft #11Example part
Ground wire from bridge—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Bridge Esquire pickup blackVolume casingWireblack
2Ground wire from bridgeVolume casingWireblack
3Volume lug1Volume casingWireground
4.047 capTone casingWireblack
5Tone casingOutput Jack sleeveWireblack
6Volume casingTone casingWireblack
7Bridge Esquire pickup white3-Way Switch pole A position 1Full output in position 1.Wirewhite
83-Way Switch pole A commonVolume lug3Wireblack
93-Way Switch pole B common3-Way Switch pole A commonThe tone's pole takes its signal from the same common.Wireblack
103-Way Switch pole A position 33-Way Switch pole A position 2Positions 2 and 3 both take the tap.Wireblack
113-Way Switch pole B position 13-Way Switch pole B position 2Wireblack
123-Way Switch pole B position 2Tone lug1The tone is in circuit in positions 1 and 2; position 3 leaves it out.Wireblack
13Bridge Esquire pickup yellow3-Way Switch pole A position 2Tapped output in positions 2 and 3.Wireyellow
14Volume lug2Output Jack tipWireblack
15Tone lug2.047 capWireblack

What each position does

SettingThe sourceEngine result
Position 1 · full output, with toneSheet: 1. Full output, with tone control.Bridge Esquire pickup (both coils).
Position 2 · tapped, with toneSheet: 2. Tapped output, with tone control.Bridge Esquire pickup (split to one coil).
Position 3 · tapped, no toneSheet: 3. Tapped output, no tone control.Bridge Esquire pickup (split to one coil).

Checked with the Tinkercaster wiring engine against the switching the source describes.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.