Skip to content
Tinkercaster

Seymour Duncan wiring

Standard Esquire with treble-bleed and fixed-filter network

Esquire · 3-way · 1V · 1T · 3.3k · .05µF

Transcribed from the manufacturer wiring sheet.

Viewed from the back of the controls, as you solder them.

Standard Esquire with treble-bleed and fixed-filter networkStandard Esquire with treble-bleed and fixed-filter network: Esquire · 3-way · 1V · 1T · 3.3k · .05µF. Original Tinkercaster drawing with labelled terminals.Bridge Esquire pickup250k250k47nF50nF50nF3.3kwhiteblackT1T2T3T4T5T6T7T8lug1lug2lug3lug1lug2lug3abtipsleevegroundabababBridge Esquire pickup3-Way SwitchVolume 250kTone 250k.047 cap · 47nFOutput JackGround wire from bridge.05 cap volume · 50nF.05 cap switch · 50nF3.3k resistor

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Bridge Esquire pickup—Vintage '54 Tele Lead STL-1Example partSame wiring for Vintage Staggered Strat SSL-1, Quarter-Pound Flat Strat SSL-4, Custom SSL-5
3-Way Switch—CRL 3-Way BladeExample part
Volume 250k250kCTS 250k Audio PotExample part
Tone 250k250kCTS 250k Audio PotExample part
.047 cap47nFOrange Drop .047µFExample part
Output Jack—Switchcraft #11Example part
Ground wire from bridge—Bridge ground wireGeneric
.05 cap volume50nFOrange Drop .05µFExample part
.05 cap switch50nFOrange Drop .05µFExample part
3.3k resistor3.3k3.3 kΩ ResistorExample part

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Bridge Esquire pickup blackVolume casingWireblack
2Ground wire from bridgeVolume casingWireblack
3Volume lug1Volume casingWireground
4.047 capTone casingWireblack
5Tone casingOutput Jack sleeveWireblack
6Volume casingTone casingWireblack
7.05 cap (to the volume casing)Volume casingWireblack
8Bridge Esquire pickup white3-Way Switch pole A position 1Wirewhite
93-Way Switch pole A position 13-Way Switch pole B commonThe hot also feeds the second pole's common.Wireblack
103-Way Switch pole A commonVolume lug3Wireblack
113-Way Switch pole A position 23-Way Switch pole B position 2Position 2: the hot reaches pole A's common through pole B.Wireblack
123-Way Switch pole A position 2Tone lug1The tone is in circuit only in position 2.Wireblack
133-Way Switch pole A position 3.05 cap (to the volume casing)Position 3: a .05 µF cap to ground on the output side.Wireblack
143-Way Switch pole A position 33.3k resistorWireblack
15.05 cap (switch)3-Way Switch pole B position 3Position 3: the hot reaches the output only through the .05 µF and the 3.3k, so the treble is heavily rolled off.Wireblack
16Volume lug2Output Jack tipWireblack
17Tone lug2.047 capWireblack
183.3k resistor.05 cap (switch)Wireblack

What each position does

SettingThe sourceEngine result
Bridge pickup with no tone controlSheet switch setting 1: bridge pickup with NO tone control.Bridge Esquire pickup.
Bridge pickup with tone controlSheet switch setting 2: bridge pickup WITH tone control.Bridge Esquire pickup.
Bridge pickup with treble rolled offSheet switch setting 3: bridge pickup with the treble heavily rolled off (no tone control).No pickup reaches the output.

Not simulated: this circuit is drawn for reference only.

  • Position 3 reaches the output only through the .05 µF capacitor and the 3.3k resistor; the engine treats a capacitor as an open circuit, so it reads that position as silent. Positions 1 and 2 match the sheet in the engine.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.