Skip to content
Tinkercaster

DiMarzio wiring

EVH original wiring with toggle selector

Neck pickup · Bridge pickup · DPDT on/on/on mini switch (EP1108) · 500K volume

DiMarzio's Ernie Ball Music Man Eddie Van Halen wiring for two-conductor pickups: each pickup's WHITE goes to an on-on-on EP1108 mini switch whose rows are jumpered, the switch feeds a 500K custom-taper volume, and there is no tone control.

Viewed from the back of the controls, as you solder them.

EVH original wiring with toggle selectorEVH original wiring with toggle selector: Neck pickup · Bridge pickup · DPDT on/on/on mini switch (EP1108) · 500K volume. Original Tinkercaster drawing with labelled terminals.Neck pickup (2-conductor)Bridge pickup (2-conductor)500kbareblackwhitebareblackwhiteT1T2T3T4T5T6lug1lug2lug3tipsleevegroundNeck pickup (2-conductor)Bridge pickup (2-conductor)DPDT on-on-on selector (EP1108)Volume 500K custom taperOutput jackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck pickup (2-conductor)—Eddie Van Halen Original NeckAs specified
Bridge pickup (2-conductor)—Eddie Van Halen Original BridgeAs specified
DPDT on-on-on selector (EP1108)—DPDT Mini-Toggle (on-on-on)Example part
Volume 500K custom taper500kCTS 500k Audio PotExample part
Output jack—Switchcraft #11Example part
Bridge ground—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

  • DiMarzio humbucker wire colors

    Red is hot, black and white join each other, green and bare go to ground. See why, and what changes when you reverse the phase.

All DiMarzio wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck pickup BLACK and BAREVolume casingWireblack
2Bridge pickup BLACK and BAREVolume casingWireblack
3Volume ground lugVolume casing (black loop)Wireblack
4Volume ground lugOutput jack sleeve (black ground run)Wireblack
5TO BRIDGE GROUNDOutput jack sleeveWireblack
6Neck pickup (2-conductor) bare shieldVolume casingShield or groundbare
7Bridge pickup (2-conductor) bare shieldVolume casingShield or groundbare
8Neck pickup WHITESelector bottom-right lugWirewhite
9Selector bottom-left lugSelector bottom-right lug (grey row jumper)Wireblack
10Bridge pickup WHITESelector top-left lugWirewhite
11Selector top-left lugSelector top-right lug (grey row jumper)Wireblack
12Selector middle-left lugSelector middle-right lug (grey row jumper)Wireblack
13Selector middle-right lugVolume input lug (grey wire)Wiresignal
14Volume middle lugOutput jack tip (grey wire)Wiresignal

What each position does

SettingThe sourceEngine result
Position 1: neckNo legend printed; named by function from the drawn rows and the EP1108 contacts.Neck pickup (2-conductor) (both coils).
Position 2: neck + bridgeNo legend printed; named by function from the drawn rows and the EP1108 contacts.Neck pickup (2-conductor) (both coils) and Bridge pickup (2-conductor) (both coils) in parallel.
Position 3: bridgeNo legend printed; named by function from the drawn rows and the EP1108 contacts.Bridge pickup (2-conductor) (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Which lever direction is position 1 is not printed; positions are named by function.
  • The pickups are drawn with their Eddie Van Halen Original catalog leads (hot, ground and bare shield), and the custom taper is not reproduced.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.