Skip to content
Tinkercaster

Seymour Duncan wiring

One humbucker on a Triple Shot ring, volume

1 humbucker · Triple Shot ring · 1V 500k

One Seymour Duncan humbucker on a Triple Shot mounting ring, straight to one 500k volume. The ring's two mini switches choose series, parallel, slug coil or adjustable coil.

Viewed from the back of the controls, as you solder them.

One humbucker on a Triple Shot ring, volumeOne humbucker on a Triple Shot ring, volume: 1 humbucker · Triple Shot ring · 1V 500k. Original Tinkercaster drawing with labelled terminals.Humbucker500kblackgreenwhiteredbareBWRGGNDOUT_WHITEOUT_BLACKOUT_BARElug1lug2lug3tipsleevegroundHumbuckerTriple Shot ringVolume 500kOutput jackBridge ground

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
HumbuckerSource: Seymour Duncan humbucker—JB Model SH-4Example partSame wiring for Duncan Custom SH-5, Duncan Distortion SH-6 Bridge, Invader SH-8 Bridge, Seymour Duncan SH-2 Jazz Bridge, Seymour Duncan SH-3 Stag Mag, Custom Five SH-14
Triple Shot ring—Triple Shot Mounting RingExample part
Volume 500k500kCTS 500k Audio PotExample part
Output jackSource: Output Jack—Switchcraft #11Example part
Bridge groundSource: Bridge ground wire—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Humbucker greenRing pad GWiregreen
2Humbucker bareRing pad GndDrawn grey.Wirebare
3Ring cable blackVolume casingWireblack
4Ring cable bareVolume casingDrawn grey.Wirebare
5Volume right lugVolume casingLug bent onto the casing under the Solder spot.Wire
6Jack sleeveVolume casingHops over the ring cable white.Wireblack
7Bridge ground wireVolume casingWireblack
8Humbucker blackRing pad BWireblack
9Humbucker whiteRing pad WWirewhite
10Humbucker redRing pad RWirered
11Ring cable whiteVolume left lugLoops down the left of the pot to the left lug.Wirewhite
12Volume middle lugJack tipWireblack

What each position does

SettingThe sourceEngine result
Triple Shot ring on seriesThe sheet's wiring: the ring's white lead is the only signal feed to the volume.Humbucker (both coils).
Triple Shot ring on parallel—Humbucker (coils in parallel).
Triple Shot ring on slug coil—Humbucker (split to one coil).
Triple Shot ring on adjustable coil—Humbucker (split to one coil).

Not simulated: this circuit is drawn for reference only.

  • Topology only: the ring's settings come from a manufacturer document rather than this sheet.
  • Each Triple Shot ring is modelled from Seymour Duncan's Triple Shot installation sheet (four settings: series, parallel, slug coil, adjustable coil); the wiring sheet draws only the ring's pads, cable and ribbon.
  • Hum cancelling and phase follow the pickups' lead colours and coil polarity as Seymour Duncan publishes them; nothing here is measured.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • Ring on series: the full humbucker reaches the volume and the jack tip.
  • Step the ring through parallel, slug coil and adjustable coil; each setting still reaches the tip.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.