Skip to content
Tinkercaster

Seymour Duncan wiring

One P-Rails, on-off-on mode switch, volume

One P-Rails · ON-OFF-ON mini-toggle (Rail / humbucker / P-90) · Volume 500k

Seymour Duncan sheet: one P-Rails with an ON-OFF-ON DPDT mini-toggle, a 500k volume and the output jack. One column of the mini-toggle is used: the red/white link on its middle lug, the black on the top lug and the green and bare on the bottom lug. Up gives the Rail coil, middle the full series humbucker, down the P-90 coil.

Viewed from the back of the controls, as you solder them.

One P-Rails, on-off-on mode switch, volumeOne P-Rails, on-off-on mode switch, volume: One P-Rails · ON-OFF-ON mini-toggle (Rail / humbucker / P-90) · Volume 500k. Original Tinkercaster drawing with labelled terminals.P-Rails500kblackgreenwhiteredbareT1T2T3T4T5T6lug1lug2lug3tipsleevegroundP-RailsON-OFF-ON mini-toggleVolume 500kOutput jackGround wire from bridge

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
P-Rails—Seymour Duncan P-RailsAs specified
ON-OFF-ON mini-toggle—DPDT Mini-Toggle (on-on-on)Example part
Volume 500k500kCTS 500k Audio PotExample part
Output jack—Switchcraft #11Example part
Ground wire from bridge—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1P-Rails greenMini-toggle bottom lugWiregreen
2P-Rails bareMini-toggle bottom lugShield or groundbare
3Mini-toggle bottom lugVolume casing (at the bent right lug)Loops under the controls and up to the volume's right side.To a pot casingblack
4Volume right lugVolume casingLug bent onto the casing.To a pot casing
5Volume casing (Solder spot)Jack SleeveWireblack
6Ground wire from bridgeVolume casing (Solder spot)To a pot casingblack
7P-Rails blackMini-toggle top lugWireblack
8P-Rails whiteMini-toggle middle lugWirewhite
9P-Rails redMini-toggle middle lugWirered
10Mini-toggle top lugVolume left lugWireblack
11Volume middle lugJack TipCarries the hops over the other wires.Wireblack

What each position does

SettingThe sourceEngine result
Mini-toggle middle: full humbucker (series)Legend: UP = Rail (single coil strat sound); MIDDLE = full humbucker sound (series); DOWN = P-90 sound.P-Rails (both coils).
Mini-toggle up: RailLegend: UP = Rail (single coil strat sound); MIDDLE = full humbucker sound (series); DOWN = P-90 sound.P-Rails (split to one coil).
Mini-toggle down: P-90Legend: UP = Rail (single coil strat sound); MIDDLE = full humbucker sound (series); DOWN = P-90 sound.P-Rails (split to one coil).
Board at rest: Mini-toggle middle: full humbucker (series)Legend: UP = Rail (single coil strat sound); MIDDLE = full humbucker sound (series); DOWN = P-90 sound.P-Rails (both coils).
Board at rest: Mini-toggle middle: full humbucker (series)Legend: UP = Rail (single coil strat sound); MIDDLE = full humbucker sound (series); DOWN = P-90 sound.P-Rails (both coils).

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • The mini-toggle is modelled with switchPosition on pole B of the catalog on-on-on mini: throw 1 = down (P-90), throw 2 = centre (off, full humbucker), throw 3 = up (Rail). Which lever direction reaches which throw follows the source legend, not a lug label.
  • The engine reports either single-coil mode as a split; which coil is the Rail and which the P-90 follows the source legend and the pickups' lead roles, not a measurement.
  • Hum cancelling and phase follow the pickups' lead colours and coil polarity as Seymour Duncan publishes them; nothing here is measured.
  • Pickup resistance is not specified, so no numeric meter readings are given.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • Mini-toggle in the middle: the meter across the jack reads the full P-Rails.
  • Mini-toggle down: the black lead and the red/white link read as one connection; up: the red/white link reads ground.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.