Skip to content
Tinkercaster

Seymour Duncan wiring

Single coil and humbucker, volume push/pull selector

Neck single · Bridge humbucker · Volume push/pull selects pickup

Transcribed from the manufacturer wiring sheet and checked against the engine.

Viewed from the back of the controls, as you solder them.

Single coil and humbucker, volume push/pull selectorSingle coil and humbucker, volume push/pull selector: Neck single · Bridge humbucker · Volume push/pull selects pickup. Original Tinkercaster drawing with labelled terminals.Neck single coilBridge pickup500kwhiteblackblackgreenwhiteredbarelug1lug2lug3sw1sw2sw3sw4sw5sw6tipsleevegroundNeck single coilBridge pickupVolume 500k push/pullOutput jackGround wire to bridge

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Single-coil black (left) lead runs down and across to the Solder spot on the volume casing.Single-coil black (left) lead runs down and across to the Solder spot on the volume casing.Wireblack
2Humbucker green lead (labelled Green & bare) to the Solder spot.Humbucker green lead (labelled Green & bare) to the Solder spot.Wiregreen
3Humbucker bare lead beside the green to the Solder spot.Humbucker bare lead beside the green to the Solder spot.Wirebare
4Volume right lug bent onto the Solder spot.Volume right lug bent onto the Solder spot.Wireground
5Wire from the Solder spot down the right side to the jack Sleeve (ground).Wire from the Solder spot down the right side to the jack Sleeve (ground).Wireground
6Arrowed wire labelled Ground wire to bridge leaves the Solder spot upwards to the right.Arrowed wire labelled Ground wire to bridge leaves the Solder spot upwards to the right.Wireground
7Single-coil white (right) lead loops over the top to the right-column bottom switch lug.Single-coil white (right) lead loops over the top to the right-column bottom switch lug.Wirewhite
8Humbucker red and white leads, labelled Red & white, end in a taped-off tip touching nothing.Humbucker red and white leads, labelled Red & white, end in a taped-off tip touching nothing.Wirered
9Humbucker lead labelled Black loops over to the right-column top switch lug.Humbucker lead labelled Black loops over to the right-column top switch lug.Wireblack
10Right-column middle switch lug loops down the left of the pot to the volume left lug.Right-column middle switch lug loops down the left of the pot to the volume left lug.Wireblack
11Volume middle lug straight down, hopping the sleeve wire, to the jack Tip (hot output).Volume middle lug straight down, hopping the sleeve wire, to the jack Tip (hot output).Wiresignal

What it does

Engine result: —

Not simulated: this circuit is drawn for reference only.

  • Push/pull volume acts as pickup selector via params.selectorByPushPull; passive position analysis does not verify both pull states against the source legend.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

    Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.