Skip to content
Tinkercaster

Seymour Duncan wiring

Tele with a neck humbucker, bridge single coil and push/pull volume coil split

One humbucker · One single coil · Three-way blade · One push/pull volume (coil split) · One tone

A Tele harness with a neck Seymour Duncan humbucker and a bridge single coil on a three-way blade, one 250k push/pull volume and one 250k tone with a .047 µF capacitor. Pulling the volume grounds the humbucker series link to split the neck pickup.

Viewed from the back of the controls, as you solder them.

Tele with a neck humbucker, bridge single coil and push/pull volume coil splitTele with a neck humbucker, bridge single coil and push/pull volume coil split: One humbucker · One single coil · Three-way blade · One push/pull volume (coil split) · One tone. Original Tinkercaster drawing with labelled terminals.Neck humbuckerBridge single coil250k250k47nFblackgreenwhiteredbarewhiteblackT1T2T3T4T5T6T7T8lug1lug2lug3sw1sw2sw3sw4sw5sw6lug1lug2lug3abtipsleevegroundNeck humbuckerBridge single coil3-Way SwitchVolume 250k push/pullTone 250k.047 cap · 47nFOutput JackGround bridge wire

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck humbuckerSource: Seymour Duncan Neck Pickup (humbucker)—Jazz Model SH-2 NeckExample partSame wiring for '59 Model SH-1 Neck, Seymour Duncan Antiquity Neck, Pearly Gates SH-PG1 Neck, Invader SH-8 Neck, Duncan Distortion SH-6 Neck, Alnico II Pro APH-1 Neck
Bridge single coilSource: Seymour Duncan Tele bridge single coil—Vintage '54 Tele Lead STL-1Example partSame wiring for Vintage Tele Rhythm STR-1, Vintage Staggered Strat SSL-1, Vintage Flat Strat SSL-2, Quarter-Pound Flat Strat SSL-4, Custom SSL-5
3-Way Switch—CRL 3-Way BladeExample part
Volume 250k push/pull250k250k Push-Pull DPDTExample part
Tone 250k250kCTS 250k Audio PotExample part
.047 cap47nFOrange Drop .047µFExample part
Output Jack—Switchcraft #11Example part
Ground bridge wireSource: bridge ground wire—Bridge ground wireGeneric

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Understand this wiring

All Seymour Duncan wiring guides →

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck humbucker greenVolume 250k push/pull casingTo a pot casinggreen
2Bridge single coil blackVolume 250k push/pull casingTo a pot casingblack
3Ground bridge wireVolume 250k push/pull casingTo a pot casingblack
4Volume 250k push/pull lug1Volume 250k push/pull casingTo a pot casing
5.047 cap bTone 250k casingTo a pot casingblack
6Tone 250k casingOutput Jack sleeveTo a pot casingblack
7Volume 250k push/pull casingTone 250k casingTo a pot casingblack
8Neck humbucker bareVolume 250k push/pull casingTo a pot casingbare
9Volume 250k push/pull sw1Volume 250k push/pull casingTo a pot casingblack
10Neck humbucker black3-Way Switch T8Wireblack
11Bridge single coil white3-Way Switch T4Wirewhite
123-Way Switch T33-Way Switch T2Jumperblack
133-Way Switch T23-Way Switch T6Jumperblack
143-Way Switch T63-Way Switch T5Jumperblack
153-Way Switch T5Volume 250k push/pull lug3Wireblack
16Neck humbucker whiteVolume 250k push/pull sw2Wirewhite
17Neck humbucker redVolume 250k push/pull sw2Wirered
18Volume 250k push/pull lug2Output Jack tipWireblack
19Volume 250k push/pull lug3Tone 250k lug1Wireblack
20Tone 250k lug2.047 cap aWireblack

What each position does

SettingThe sourceEngine result
Neck, knob down—Neck humbucker (both coils).
Neck + bridge, knob down—Neck humbucker (both coils) and Bridge single coil in parallel.
Bridge, knob down—Bridge single coil.
Neck, knob pulled—Neck humbucker (split to one coil).
Neck + bridge, knob pulled—Neck humbucker (split to one coil) and Bridge single coil in parallel.
Bridge, knob pulled—Bridge single coil.

Checked with the Tinkercaster wiring engine against the switching the source describes.

  • Hum cancelling and phase follow the pickups' lead colours and coil polarity as Seymour Duncan publishes them; nothing here is measured.
  • The source does not say which knob position splits; this follows the usual push/pull behaviour (pulled joins the middle lugs to the lugs nearest the pot).

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • Knob down: each blade position reads the selected full pickup(s).
  • Knob up: the humbucker(s) on the push/pull drop to roughly one coil.
  • With the volume at zero, tip and sleeve should read as a short in every position.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.