Skip to content
Tinkercaster

Seymour Duncan wiring

Three Live Wire active singles, five-way blade, volume and two tones

3 Live Wire actives · 5-way blade · 100k volume · Two 100k tones (neck, middle; shared .022) · Stereo jack · Two 9 V batteries

Three Seymour Duncan Live Wire active single coils on a five-way blade into a 100k master volume and two 100k tones (middle and neck) that share one .022 cap through the second pole of the blade. Two 9-volt batteries in series feed the joined red pickup leads, and the stereo jack's ring switches the battery negative.

Viewed from the back of the controls, as you solder them.

Three Live Wire active singles, five-way blade, volume and two tonesThree Live Wire active singles, five-way blade, volume and two tones: 3 Live Wire actives · 5-way blade · 100k volume · Two 100k tones (neck, middle; shared .022) · Stereo jack · Two 9 V batteries. Original Tinkercaster drawing with labelled terminals.Neck Live WireMiddle Live WireBridge Live Wire100k9V9V100k100k22nFwhitebareredwhitebareredwhitebareredT1T2T3T4T5T6T7T8lug1lug2lug3tipsleevering+−+−lug1lug2lug3lug1lug2lug3abNeck Live WireMiddle Live WireBridge Live Wire5-way bladeMaster volume 100kOutput jack (stereo)Battery 1 clipBattery 2 clipTone 100k (upper)Tone 100k (lower).022 cap · 22nF

Open the interactive diagram to zoom, move components and try the switches.

Parts and values

In the drawingValuePart
Neck Live Wire—Live Wire Active Single CoilAs specified
Middle Live Wire—Live Wire Active Single CoilAs specified
Bridge Live Wire—Live Wire Active Single CoilAs specified
5-way bladeSource: 5 Way Blade—Oak Grigsby 5-WayExample part
Master volume 100k100k100K PotGeneric
Output jack (stereo)Source: OUTPUT JACK(stereo)—Switchcraft #12BExample part
Battery 1 clipSource: 9-Volt Battery (left)—9V Battery ClipExample part
Battery 2 clipSource: 9-Volt Battery (right)—9V Battery ClipExample part
Tone 100k (upper)100k100K PotGeneric
Tone 100k (lower)100k100K PotGeneric
.022 cap22nFOrange Drop .022µFExample part

Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.

Connections

In soldering order: grounds first, then the switch, the pickups and the signal path.

#FromToHow
1Neck Live Wire bare leadMaster volume 100k casing (Solder spot)To a pot casingbare
2Middle Live Wire bare leadMaster volume 100k casing (Solder spot)To a pot casingbare
3Bridge Live Wire bare leadMaster volume 100k casing (Solder spot)To a pot casingbare
4Master volume 100k third lugMaster volume 100k casing (Solder spot)Lug bent up onto the casing.To a pot casing
5Master volume 100k casing (Solder spot)Output jack (stereo) Sleeve (ground)To a pot casingblack
6.022 cap leg BTone 100k (upper) casing (Solder spot)To a pot casingblack
7Tone 100k (upper) casing (Solder spot)Tone 100k (lower) casing (Solder spot)To a pot casingblack
8Tone 100k (upper) casing (Solder spot)Master volume 100k casing (Solder spot)To a pot casingblack
9Neck Live Wire white lead5-way blade pickup-side row, third lug from top (neck)Wirewhite
10Middle Live Wire white lead5-way blade pickup-side row, second lug from top (middle)Wirewhite
11Bridge Live Wire white lead5-way blade pickup-side row, top lug (bridge)Wirewhite
125-way blade pickup-side row, bottom lug (common)5-way blade second row, top lug (common)Wireblack
135-way blade second row, top lug (common)Master volume 100k input lugWireblack
145-way blade second row, third lugTone 100k (lower) first lug (left)Wireblack
155-way blade second row, bottom lugTone 100k (upper) middle lugWireblack
16Neck Live Wire red leadBattery 2 clip red leadWirered
17Middle Live Wire red leadBattery 2 clip red leadWirered
18Bridge Live Wire red leadBattery 2 clip red leadWirered
19Master volume 100k middle lugOutput jack (stereo) Tip (hot output)Wireblack
20Battery 1 clip black leadOutput jack (stereo) Ring (battery ground)Wireblack
21Battery 1 clip red leadBattery 2 clip black leadJoined inside a drawn sleeve between the two batteries.Wirered
22Tone 100k (upper) third lug (lower right, cap lug).022 cap leg AWireblack
23Tone 100k (lower) middle lugTone 100k (upper) third lug (lower right, cap lug)Wireblack

What each position does

SettingThe sourceEngine result
BridgePositions are not printed on the sheet; derived from the standard five-way contact table. Active pickups: wiring topology only. No tone on the signal (second-pole map by function).No pickup reaches the output.
Bridge + middlePositions are not printed on the sheet; derived from the standard five-way contact table. Active pickups: wiring topology only. Lower (middle) tone on the signal (second-pole map by function).No pickup reaches the output.
MiddlePositions are not printed on the sheet; derived from the standard five-way contact table. Active pickups: wiring topology only. Lower (middle) tone on the signal (second-pole map by function).No pickup reaches the output.
Middle + neckPositions are not printed on the sheet; derived from the standard five-way contact table. Active pickups: wiring topology only. Both tones on the signal (second-pole map by function).No pickup reaches the output.
NeckPositions are not printed on the sheet; derived from the standard five-way contact table. Active pickups: wiring topology only. Upper (neck) tone on the signal (second-pole map by function).No pickup reaches the output.

Not simulated: this circuit is drawn for reference only.

  • Active Live Wire pickups and their battery supply are not simulated (engine limit: active); the board is wiring topology only.
  • The sheet prints 100k with no taper; the audio taper of the catalog part is an assumption.
  • Which pickup each tone follows depends on the second-pole lug map made by function; the sheet does not state it.

Before you solder

Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .

Check before plugging in

  • With no plug in the jack, the battery negative should read open to ground; with a stereo plug inserted, the ring should connect it to the sleeve.
  • The joined red leads should read the battery positive (the two batteries in series) against ground with a plug inserted.

Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.