Parts and values
| In the drawing | Value | Part |
|---|---|---|
| Neck pickup | — | Little '59 SL59-1 Neck (Strat-size) |
| Middle pickup | — | Little '59 SL59-1 Neck (Strat-size) |
| Bridge pickup | — | JB Jr. SJBJ-1 Bridge (Strat-size) |
| 5-Way Switch | — | Oak Grigsby 5-Way |
| Volume 250k push/pull | 250k | 250k Push-Pull DPDT |
| Tone 250k | 250k | CTS 250k Audio Pot |
| .047 µF tone cap | 47nF | Orange Drop .047µF |
| Output Jack | — | Switchcraft #11 |
| Ground wire to bridge | — | Bridge ground wire |
Every pickup is the maker's own. “As specified” means the sheet names that part. “Example part” means the sheet names no model: the pickup shown is one of the maker's with the same leads, and any pot, cap or switch with the same value and lugs will do. “Generic” is a plain part such as a ground wire. “Not on the sheet; stand-in” means the sheet prints no value for that part, so the value shown is the usual one, not the maker's.
Understand this wiring
- Seymour Duncan humbucker wire colors
See the pickup, recognise its two halves, and learn where each coloured wire goes.
- Seymour Duncan coil splitting explained
A humbucker has two coils. See how a switch lets you use just one of them.
- Reading Seymour Duncan push/pull switch diagrams
Turning the knob and pulling it do different jobs. See the actual part, then try its switch connections.
Connections
In soldering order: grounds first, then the switch, the pickups and the signal path.
| # | From | To | How |
|---|---|---|---|
| 1 | Neck pickup gnd | Volume 250k push/pull casing | Wire |
| 2 | Neck pickup bare | Volume 250k push/pull casing | Wire |
| 3 | Middle pickup black (white lead, ground) | Volume 250k push/pull casing | Wire |
| 4 | Middle pickup bare | Volume 250k push/pull casing | Wire |
| 5 | Middle pickup hot (black) | Middle pickup gnd (green) | Wire |
| 6 | Bridge pickup gnd | Volume 250k push/pull casing | Wire |
| 7 | Bridge pickup bare | Volume 250k push/pull casing | Wire |
| 8 | Ground wire to bridge ground | Volume 250k push/pull casing | Wire |
| 9 | Volume 250k push/pull lug1 | Volume 250k push/pull casing | Wire |
| 10 | Volume 250k push/pull casing | Output Jack sleeve | Wire |
| 11 | .047 µF tone cap b | Tone 250k casing | Wire |
| 12 | Tone 250k casing | Volume 250k push/pull casing | Wire |
| 13 | Middle pickup series link | Volume push/pull pole B common | Wire |
| 14 | Volume push/pull pole A up | Volume casing | Wire |
| 15 | Bridge pickup hot | 5-Way Switch T3 | Wire |
| 16 | Middle pickup white (red lead, hot) | 5-Way Switch T1 | Wire |
| 17 | Neck pickup hot | 5-Way Switch T2 | Wire |
| 18 | 5-Way Switch T4 | Volume 250k push/pull lug3 | Wire |
| 19 | Neck pickup series link | 5-Way Switch T6 | Wire |
| 20 | Bridge pickup series link | 5-Way Switch T7 | Wire |
| 21 | 5-Way Switch T8 | Volume push/pull pole A common | Wire |
| 22 | Neck pickup white | Neck pickup red | Wire |
| 23 | Bridge pickup white | Bridge pickup red | Wire |
| 24 | Volume 250k push/pull lug2 | Output Jack tip | Wire |
| 25 | Volume 250k push/pull lug3 | Tone 250k lug1 | Wire |
| 26 | Tone 250k lug2 | .047 µF tone cap a | Wire |
| 27 | Volume push/pull pole B up | Volume push/pull pole A up | Wire |
What each position does
| Setting | The source | Engine result |
|---|---|---|
| Position 1 · push | Sheet: push/pull down, all pickups are hum-cancelling. | Bridge pickup (both coils). |
| Position 1 · pull | Sheet: push/pull up, all pickups are true single coils. | Bridge pickup (split to one coil). |
| Position 2 · push | Sheet: push/pull down, all pickups are hum-cancelling. | Middle pickup (both coils) and Bridge pickup (both coils) in parallel. |
| Position 2 · pull | Sheet: push/pull up, all pickups are true single coils. | Middle pickup (split to one coil) and Bridge pickup (split to one coil) in parallel. |
| Position 3 · push | Sheet: push/pull down, all pickups are hum-cancelling. | Middle pickup (both coils). |
| Position 3 · pull | Sheet: push/pull up, all pickups are true single coils. | Middle pickup (split to one coil). |
| Position 4 · push | Sheet: push/pull down, all pickups are hum-cancelling. | Neck pickup (both coils) and Middle pickup (both coils) in parallel. |
| Position 4 · pull | Sheet: push/pull up, all pickups are true single coils. | Neck pickup (split to one coil) and Middle pickup (split to one coil) in parallel. |
| Position 5 · push | Sheet: push/pull down, all pickups are hum-cancelling. | Neck pickup (both coils). |
| Position 5 · pull | Sheet: push/pull up, all pickups are true single coils. | Neck pickup (split to one coil). |
Checked with the Tinkercaster wiring engine against the switching the source describes.
- Three-way coil-split on one DPDT push/pull is transcribed as drawn; pull/up position analysis is topology-only.
Before you solder
Ticks are kept in this browser only, as a reminder. They are not a check of your joints. New to soldering? Read the soldering cheat sheet .
Check before plugging in
Measure across the output jack with a multimeter on its resistance range. No exact readings are given where the source does not specify the pickups.